A weld nut, a weld screw or a weld-stud element leaves this plant as a component, with a thread in the as-manufactured condition required by the print. The customer’s welding process can, in service, introduce heat, spatter or distortion that later affects gauging. If the thread must still accept a gauge after that weld, the condition has to be written down and the method agreed. The weld itself is not performed here as a complete assembly, and a thread that gauges on the loose part is not automatic evidence of the same result after a weld that has not been specified as part of the order.

What has to be visible on the revision or the order

A complete requirement states whether the thread is inspected on the loose component, after a defined customer weld, or both, and it names the gauge or the standard to be used. If a go thread must enter after welding, or if a no-go condition is also defined, those checks belong in the plan. “Thread must be OK after welding” without a gauge, a timing, or a statement of who performs the weld is not complete. The thread class and the gauging method on the component itself follow the same discipline already set out in the notes on thread standards, pitch and gauging and on internal threads.

Related features should be consistent with that requirement. A pilot, a closed end, a coating in the thread, or a masking note can all change what is possible after heat is applied. Those items are taken from the current revision, not inferred from a catalogue weld nut or from weld screws and weld-stud elements used only as examples.

What is supplied, and what remains the customer’s process

SUNHY quotes the fastener as a part. Welding the nut or the screw to a panel, setting current and time, and designing the fixture stay with the customer unless a written agreement says otherwise. Advice that a thread should be protected during welding is not the same as performing that protection, and it is not a warranty of the welded joint. The same boundary is used in the notes on weld nuts produced from the print and on pierce nuts and pierce elements, where the customer’s press process is likewise not quoted as a SUNHY assembly.

If a thread plug, a cap, a heat-resistant mask, or a defined cleaning step after welding is to be part of the supply, it has to be named on the order. Partial coating and masking, when they are specified for the as-supplied part, follow the print as in the note on partial coating and masking. They are not added silently “because the part will be welded”.

Coating, lubrication and the thread after heat

A coating in the thread, a dry-film lubricant, or an oil used for protection can change after the customer applies weld heat. If the print requires a coating and also requires the thread to gauge after welding, that combination is reviewed rather than assumed to be compatible. Coating of internal threads, where specified, follows the note on coating on internal threads. A familiar zinc-flake or electroplated system is not selected “to help the weld” in place of the specified finish.

Inspection on the loose part, and any agreed after-weld check

Unless the order says otherwise, thread gauging is performed on the loose component, before despatch. If a demonstration after welding is required, the weld process, the panel, the gauge and the responsibility have to be agreed in writing. A sample welded in a development shop with a different gun or a different panel is not automatic approval of a later production weld. First-article inspection, when required, should state clearly which thread condition is being reported, as in the note on first-article inspection.

Evidence such as a gauge record, photographs, or an EN 10204 3.1 statement of the as-manufactured thread is confirmed per order when required. It is not a type-approval of the customer’s welded assembly, and it does not replace a condition that was never written down.

Conflicts and open items

A print that demands a full coating in the thread and a tight after-weld gauge, or that shows a thin wall beside a large weld projection without stating the after-weld condition, is flagged. Mixed notes in a weld specification and a fastener drawing are reviewed together. Those conflicts are resolved on the revision or in a written order comment, not on the shop floor during packing.

Prototype welds and volume

A short sample lot is sometimes welded in a laboratory or in a development fixture that will not be used in series. If the after-weld thread condition is part of the approval, the weld used for that demonstration should represent the production-intent process, or the difference should be written down. A go gauge that passes after a gentle development weld is not evidence that the same nut will gauge after a production weld with a different heat input. Volume and the proposed component route still belong in the enquiry, because a change of thread method or of coating on the loose part can also change what is presented to the customer’s weld.

If the print is silent on the after-weld condition, the quotation is for the loose-part thread only. That silence is flagged so that the customer can add a requirement or confirm that the loose-part condition is enough. It is not filled in with a default after-weld promise.

What to send with the RFQ

Send the current drawing revision, the thread class and any after-weld requirement, together with the material, finish and volume. If a thread plug, a masking step, or a demonstration after a defined weld is already decided, name it. Unspecified points will be flagged before production rather than assumed.

This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.