An internal thread on a made-to-print nut, weld nut, clinch nut or component is a drawing-controlled feature: the system, the size, the pitch, the class of fit, the useful depth, and the gauging condition, including after coating when that is required. Whether the thread is cut or formed is a process decision when the print does not mandate it, and it is stated rather than assumed. A catalogue nut thread, or a tap that happens to be on the shelf, is not a substitute for the call-out on the current revision.

SUNHY reviews internal threads on special nuts and installation elements, on weld nuts and on threaded features of turned parts, against the customer drawing. The notes on thread standards, pitch and gauging and on rolled versus cut threads cover the general rules; this article looks at the internal case, including useful depth, chip-grooves or runout, and gauging before and after coating.

What the revision has to make visible

A complete call-out names the thread system, size, pitch, class of fit and hand, together with the useful or gauge depth and any incomplete thread, countersink or runout at the start and at the bottom of the hole. A through hole and a blind hole are different pictures. “Tap to suit the bolt” or “standard nut thread” is not a dimension. If a customer or industry standard already defines the internal thread and its gauges, it should be named on the revision or attached to the enquiry.

The start of the thread — a countersink, a chamfer, a lead-in — and any undercut or chip-groove at the bottom have to be consistent with the useful depth and with the remaining wall or the weld geometry. Those features are not added as a convenience so that a tap can run closer to a shoulder than the print allows. Related geometry on external threads is discussed in the notes on thread runout and on useful thread length; the same discipline applies inside the hole.

Cut threads, formed threads and later changes

Cut (tapped) and formed (rolled) internal threads leave different material flow, different residual stress and a different minor diameter for the same nominal size. The method is a process decision and is stated rather than assumed, unless the print itself requires one or the other. A formed sample is not approval of a later cut thread, or the reverse. A change of tap, of forming tool, or of the hole size before threading is a process change and is re-validated before serial release — see the notes on secondary operations and on prototype samples and series production.

Installation nuts — clinch nuts, rivet nuts, weld nuts and T-nuts — still have an internal thread that must be produced and gauged as specified after the installation features have been formed. One feature is not used to excuse the other. Those families are already discussed in the notes on clinch nuts and rivet nuts, on weld-nut projections and on T-nuts and special installation nuts.

Coating and the gauging condition

Coating builds on an internal thread and can change how a gauge feels, especially in a fine pitch or a tight class of fit. If the finished, coated thread must still accept a go gauge and refuse a no-go, that condition has to be written down. Over-tapping “to make plating work”, or a change from forming to cutting after coating trials, is a process decision that must follow the print, not an informal shop practice. A lubricant, a wax or a sealer in the thread is part of the finished condition when the specification includes it; informal oiling is not.

Heat treatment can move a small nut or a thin-walled component. If a tight class is required after heat treatment and coating, the sequence belongs in the agreed route. Those process-condition rules are the same as in the notes on heat treatment and on coatings already published on the site. On high-strength nuts, any hydrogen-embrittlement control is named with the coating when it applies.

Inspection of the internal thread

Go / no-go gauges, a measured pitch diameter, a useful-depth check, or a layout of the countersink are used when the print or the order requires that evidence, not automatically in every possible form. If a particular gauge set, including after coating, is already decided, name it. A bolt that “screws in” is not a substitute for the gauges that the class of fit requires. First-article or layout inspection, when required, should be planned on the production-intent route, including the threading method and the coating state in which the thread will be gauged. That rule is the same as in the note on first-article inspection.

Property class or proof load on a nut, when it is specified, is a separate characteristic from the thread class of fit. Both have to be visible on the revision that is quoted. That subject is developed in the note on nut property grades 8, 10 and 12, and it does not replace the gauging of the internal thread.

What to write in the RFQ

Quote the internal thread — system, size, pitch, class, hand, useful depth and any countersink or runout — together with the gauging condition, including after coating if required, the method if the print already mandates cut or formed, the material, the property class, the finish, the volume and the documents you need, all as they appear on the current revision. Send the print with the request form.

Send the print. The scope is confirmed before quote.

Email the current drawing revision, or use the request form. Unspecified points will be flagged before production rather than assumed.

This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.