Heat treatment on a made-to-print fastener is part of the process route, not a finishing touch that can be decided after the part is formed. The property class, the material grade and any hardness or case-depth call-out on the current revision decide whether the part is quenched and tempered, carburized, annealed, or left in the as-formed or as-machined condition. A route used on a similar item is not reused automatically.

SUNHY reviews heat treatment against the customer drawing on bolts, screws and studs and on other fasteners that carry a class or a heat-treatment note. The routes named on the quality page — quench and temper to the stated property class, carburizing, and annealing, as applicable to the grade and the drawing — are the starting point for that review. They are not a menu from which a treatment is selected to “improve” an unspecified part.

What the print has to state

The drawing, or a specification that the drawing invokes, should name the property class or the required hardness, and the material grade. If a case depth, a core-hardness range, or a surface-condition requirement such as a limit on decarburization is already decided, it should be visible on the revision that is quoted. “Heat treated” without a class, a hardness or a referenced standard is an open item, not a complete instruction.

Where only a material grade is shown, the heat-treatment condition still has to be clear: annealed bar, a headed and then hardened condition, or a stainless condition that is not a carbon-steel class. Inconsistencies between the grade, the class and the heat-treatment note are flagged before production rather than resolved on the shop floor.

Quench and temper, carburizing and annealing

Quench and temper is the usual route toward property classes such as 8.8, 10.9 and 12.9 when those classes are specified on carbon or alloy steel. Carburizing is used when the print calls it up, typically together with a case-depth or surface-hardness requirement. Annealing is applied where the grade and the drawing require a softened condition, including as an intermediate step on some routes. None of these is added as a default.

The sequence relative to threading, machining and coating has to be planned. A thread may be rolled or cut before heat treatment, or in some cases after, depending on the print and the method; coating almost always follows heat treatment. Distortion, thread condition and the need for any subsequent sizing or gauging are reviewed as part of that sequence, not after the first serial lot.

Evidence is added when the order requires it

Mechanical evidence — hardness, proof load, tensile properties — is added to the inspection plan when the order requires it, not automatically on every lot. If a particular method, a sample size or a location for hardness readings is already defined, name it. The companion notes on hardness and tensile checks and on property classes describe how those requirements are read from the print.

Material documents such as EN 10204 3.1 are confirmed per order, as set out in the note on documents that can be confirmed per order. A heat-treatment chart or a hardness record is included when it is specified, not as a blanket attachment to every shipment.

Coatings and high-strength parts

On high-strength parts, especially at 10.9 and 12.9, the coating system and any required hydrogen-embrittlement control have to be named with the heat-treatment requirement. Those points are covered in the existing note on coatings for high-strength fasteners and are not repeated at length here. Heat treatment does not, by itself, choose a coating, and a coating trade name does not, by itself, choose a heat-treatment recipe.

A change of heat-treatment source, recipe or sequence is a process change. It is re-validated before serial release, in the same way as a change from a machined prototype route to a headed series route. The note on prototype samples and series production applies equally here.

Starting material, distortion and the rest of the route

The starting material has to be suitable for the intended treatment. A heading wire, a bar grade or a free-machining variant is not interchangeable with the specified steel simply because both can be heat-treated. Grades that appear as examples on this site — 10B21, 1010, 1018, 35CrMo / 42CrMo, SCM435 — are reviewed when they are written on the print. The certificate, when it is required, has to match that grade, as described in the note on matching the material grade to the certificate.

Heat treatment can move a thread, a shank or a bearing face. If a tight runout, a fine thread class, or a long thin shank is on the print, the risk of distortion is part of the review, and any subsequent sizing, straightening or gauging has to be planned and agreed. Straightening is not an informal recovery step. If it is used, it is part of the documented route, and it must still leave the part inside the drawing limits, including after coating.

What to write in the RFQ

Include the property class or hardness, the material grade, any case-depth or core-hardness call-out, and the coating, as they appear on the current revision. State the mechanical evidence and documents you need, each of which is confirmed per order. Send the drawing with the request form or to anna@sunhyings.com. A wider list of enquiry items is in what to include in a made-to-print RFQ.

This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.