Some made-to-print parts are not coated all over. A thread may have to remain uncoated, a shank or a sealing diameter may be masked, a head may be coated and a point left bare, or a selective finish may be applied to only one end of a stud. Those choices are drawing-controlled when the print states them. They are not improvised at the coating line because a gauge was tight, because a weld area should stay clean, or because a similar commercial part is only plated on the head.
What has to be visible on the revision
A complete call-out names the coated and uncoated zones, the boundary, any masking or plugging method if the specification requires one, and the coating system that applies to the coated zone. “Mask threads as required” or “keep the shank clean” without a length, a diameter or a view is not complete. If a customer standard already defines a partial-coating scheme, it should be named on the revision or attached to the enquiry. The uncoated zone still has to meet its own dimensional, thread and surface requirements.
Partial coating changes both appearance and functional surfaces. A masked thread must still gauge in the specified condition; a masked weld or press feature must still meet its geometry. Those adjacent requirements are reviewed together with the coating note, as in the notes on coating thickness and thread class and on thread gauging.
Masking is a stated process step
Plugs, caps, tapes, mechanical masks or a process that simply does not wet a zone are process choices and are stated rather than assumed. A sample that was fully coated and then stripped on a bench is not approval of a later masked production route, or the reverse. Adding, moving or omitting a mask after samples have been approved is a process change and is re-validated before serial release. The same discipline applies to other selective operations described in the note on secondary operations.
Masking of a thread, a shank or a head so that a region remains soft during heat treatment is a different requirement again and belongs with the heat-treatment call-out, as in the note on case hardening. It is not used as an informal substitute for a coating mask, or the reverse.
Inspection of both zones
Thickness and appearance on the coated zone, and dimensions, thread gauges or a cleanliness check on the uncoated zone, are used when the print or the order requires that evidence, not automatically in every possible form. If a particular mask line, a first-article photograph, or a gauge condition for the uncoated thread is already decided, name it. A visual check that “the thread looks bare” is not a substitute for a remaining-coating limit or a gauge result written on the print. Certificates and any EN 10204 3.1 evidence are confirmed per order when required.
Open items and conflicts
A print that requires a full-coverage salt-spray hour figure and also a large uncoated functional area, or that shows a mask on one view and full coverage in a note, is flagged. Those conflicts are resolved on the revision, not by a verbal instruction to the coater. An IMDS entry, when required, has to reflect the actual coated and uncoated condition.
Boundaries have to be inspectable
A mask line that sits on a radius, in a thread runout, or across a sealing face can be difficult to hold and difficult to inspect. If the print places a boundary in such a zone, the method and the inspection of that boundary should be agreed before tools and masks are committed. A ragged or creeping coating edge is not tidied away with an informal wipe after approval of samples. Related geometry at runouts and undercuts is already discussed in the notes on thread runout and on undercuts and neck grooves.
Volume and the proposed masking method also belong in the enquiry. A hand-masked prototype is not automatic approval of a later cap or fixture route, and a change of mask method after samples have been approved is a process change. First-article inspection, when required, should be planned on the production-intent mask and coating route, as in the note on first-article inspection. The current drawing revision remains the source of the coated and uncoated zones in every case.
The enquiry should also say how the uncoated zone will be protected in transit if cleanliness or rust prevention matters after masking, and whether any later assembly oil is permitted on that zone. Those steps can otherwise undo a carefully masked surface. If a weld end, a press feature, or a sealing diameter is the reason for the mask, the mating-part drawing can be attached for information; it is not used to invent the mask length. First-article inspection, when required, should record both the coated and the uncoated condition on the production-intent route, including any thread-gauge state that the print requires.
What to send with the RFQ
Send the current drawing revision, the coating specification, and clear views or dimensions of the masked or uncoated zones. If a particular masking method or a first-article check of the boundary is already decided, name it. Volume belongs in the enquiry because some mask methods depend on quantity. Unspecified points will be flagged before production rather than assumed.
This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.