Coating builds on an internal thread as well as on an external one. On a made-to-print nut, weld nut, clinch nut, union nut or other component, that build-up can change the minor diameter, the feel of a gauge, and the fit with the mating bolt or stub. The current revision has to make the coating system, the class of fit and the gauging condition visible, including after coating when that is required. Over-tapping “to make plating work”, or a change from forming to cutting after coating trials, is a process decision that must follow the print, not an informal shop practice.

What has to be visible on the revision

A complete call-out names the internal thread system, size, pitch and class of fit, the coating, and whether the thread is gauged before coating, after coating, or both. “Tap to suit the bolt, then plate” or “standard nut thread, coated” is not a dimension. If a customer or industry standard already defines the internal thread, the reserved allowance and the gauges, it should be named on the revision or attached to the enquiry. The same completeness is already required in the note on internal threads: tapping, forming and gauging.

Union nuts and other gas-equipment accessories follow the same rule. A brass or steel union nut is a component, not a complete regulator or station, and its internal thread and coating are still taken from the print, as in the notes on brass connecting stubs and union nuts and on coating thickness and thread class.

Cut, formed and coated threads are different routes

Cut (tapped) and formed (rolled) internal threads leave a different minor diameter and a different surface for the same nominal size. Coating then fills that surface. The threading method is a process decision when the print does not mandate it, and it is stated rather than assumed. A formed sample is not approval of a later cut thread, or the reverse, especially when post-coat gauging is required. A change of tap, of forming tool, or of the hole size before threading, after samples have been approved, is a process change and is re-validated before serial release.

A lubricant, a wax or a sealer in the thread is part of the finished condition when the specification includes it; informal oiling is not. Both can change how a gauge feels, as in the note on lubrication, dry-film and friction modifiers.

Gauging after coating is used when specified

Go / no-go gauges, a measured pitch diameter, or a useful-depth check are used when the print or the order requires that evidence, not automatically in every possible form. If a particular gauge set, including after coating, is already decided, name it. A bolt that “screws in” is not a substitute for the gauges that the class of fit requires. First-article inspection, when required, should be planned on the production-intent route, including the threading method and the coating state in which the thread will be gauged, as in the note on first-article inspection.

Open items and conflicts

A print that requires a heavy coating and a tight internal class without an allowance, or that asks for a fully coated salt-spray performance and also a gauge-perfect internal thread without saying how both are met, is flagged. Partial coating of the internal thread, if it is intended, must be on the print, as in the note on partial coating and masking.

Mating parts do not invent the internal allowance

Compatibility with a bolt, a stub or a pipe thread is a design decision on the customer side. Two parts can be reviewed as a pair if both drawings are sent; one drawing is not used to invent an over-tap, a class of fit, or a post-coat gauge condition on the other. “To suit our bolt after plating” is not a dimension. If a customer standard that defines the internal allowance is already chosen, it should be named on the revision or attached to the RFQ, as in the note on useful thread length and engagement.

Volume and the proposed threading and coating route also belong in the enquiry. A thread that can be cut and plated on a prototype may be intended for a formed and barrel-plated route in series, and the residual hole size will not be the same in every method. Those choices are stated in the quotation, and they are not changed after samples have been approved without a review. First-article inspection, when required, should be planned on the production-intent route, as in the note on first-article inspection.

The enquiry should also identify whether the nut, union nut or component is delivered as a loose part or as part of a captured or pre-assembled element, because coating and gauging sequences change when another part is already present. Captured washers and similar assemblies are discussed in the existing note on that subject; they do not remove the need to state the internal-thread condition. If a particular over-tap, a hole size before threading, or a gauge set after coating is already decided, name it. A change of that sequence after samples have been approved is a process change and is re-validated before serial release.

What to send with the RFQ

Send the current drawing revision, the coating specification, the internal-thread class, and any standard that defines post-coat gauging. If a particular gauge set or a first-article check is already decided, name it. Volume belongs in the enquiry. Unspecified points will be flagged before production rather than assumed.

This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.