Weld screws and weld-stud elements carry a thread on one side and a weld end, a collar, or another weld feature on the other. On a made-to-print order they are quoted as components produced to the current revision. The weld-end geometry, the thread, the material or property class, and the finish are taken from the print. They are not quoted as welded assemblies, and SUNHY does not perform the customer’s welding as a complete assembly unless a written agreement says otherwise. A catalogue weld stud is not a substitute for the dimensions on the drawing.

What has to be visible on the revision

A complete call-out names, for the weld end, the diameter, the length or protrusion, any collar, flange, point or location feature, and the weld-related geometry the print shows. For the threaded end it names the thread system, size, pitch, class of fit, useful length and point or chamfer. Material, property class and finish belong on the same revision. “Weld stud to suit the sheet” or “standard weld screw” without those details is not complete. If a customer standard already defines the element, it should be named on the revision or attached to the enquiry.

Weld-related geometry follows the same made-to-print rule already used on weld nuts and on weld projections and location features. Pilots, collars and projections are produced as drawn; welding parameters remain the customer’s process. If the thread must still gauge after the customer’s weld, that condition has to be stated rather than assumed.

Components, not welded assemblies

The scope is the screw or the stud as a part. Sheet, brackets and the finished welded joint stay with the customer. A sample welded onto a convenient coupon in a trial is not automatic approval of the customer’s production weld, and it is not a process sign-off for the welding operation. If both the stud drawing and the mating-sheet drawing are sent, they can be reviewed as a pair so that the printed weld end can be produced and inspected; one drawing is not used to invent missing geometry on the other.

Thread, coating and inspection

Thread and drive or weld-end gauging, hardness when a hardenable grade or a specified condition requires it, and first-article inspection follow the print in the same way as on other fasteners. Coating on the thread, and any mask of the weld end, must be on the print if they are required, as in the notes on coating thickness and thread class and on partial coating and masking. A visual check that “there is a weld bump and a thread” is not a substitute for the diameters and the lengths written on the print. Certificates and any EN 10204 3.1, PPAP or IMDS evidence are confirmed per order when required.

Open items and conflicts

A print that leaves the weld end as a sketch without dimensions, or that requires a full-coverage coating and also a bare weldable surface without a mask, is flagged. A change of weld-end punch or of threading method after samples have been approved is a process change and is re-validated before serial release. Property class remains a print call-out, as in the note on property classes.

Heading, turning and welding trials stay on different sides of the scope

A weld screw or stud may be headed, turned, or produced on a mixed route. That choice is a process decision and is stated rather than assumed. A machined sample is not approval of a later headed weld end, or the reverse, because formed and machined weld features do not have the same radii or the same face. Tooling changes on the component are process changes, as in the notes on cold heading versus CNC and on cold-heading tooling.

Volume and the proposed route also belong in the enquiry. Welding trials, when the customer asks for them, remain evidence about the component’s printed weld end; they do not turn the quotation into an assembly contract. First-article inspection, when required, should be planned on the production-intent route, including any mask of the weld end and any post-coat thread condition, as in the note on first-article inspection. The current drawing revision remains the source of the weld-end and thread requirement in every case.

The enquiry should also include any requirement for orientation, packing, or a mask of the weld end, and any post-weld thread-gauge condition that the customer already intends to impose on the component. Those notes help the printed weld end and the threaded end to be produced consistently; they still do not turn the order into a welded assembly. Material and property class remain print call-outs, and a neighbouring grade is not substituted to make welding easier, as in the note on material substitution. First-article inspection, when required, inspects the element as drawn.

What to send with the RFQ

Send the current drawing revision of the screw or stud, the material and finish specifications, and any customer standard that defines the weld end. If a mating-sheet drawing, a first-article weld trial, or a post-weld thread-gauge condition is already required, attach that information; it is not used to invent missing dimensions on the element. Volume belongs in the enquiry. Unspecified points will be flagged before production rather than assumed.

This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.