Pierce nuts and related pierce elements are installation fasteners that are intended to be set into a panel in the customer’s press or assembly process. On a made-to-print order the nut or the element is quoted as a component produced to the current revision. Panel thickness, hole or pierce conditions, and the geometry of the piercing or clinching feature are drawing inputs when the print states them. The customer’s press process, the die in the press, and the finished welded or pressed assembly are not quoted as a SUNHY assembly, and a catalogue pierce nut is not selected “to suit” an unstated panel.

What has to be visible on the revision

A complete call-out names the body form, the piercing or retention geometry, the thread, the material or property grade, the finish, and the panel or hole conditions that the element is designed to meet. “Pierce nut to suit 1.5 mm panel” or “standard self-piercing nut” without those details is not complete. If a customer standard already defines the element and the panel conditions, it should be named on the revision or attached to the enquiry. Related installation elements are discussed in the existing notes on clinch nuts and rivet nuts and on weld nuts and special nuts; a pierce nut is not substituted for those forms, or the reverse, just because all three end up in a sheet-metal joint.

Thread class, coating and any requirement to gauge the thread after the customer’s installation, if that condition is specified, have to be visible. Coating build on the internal thread follows the same rule as on other nuts, as in the notes on internal threads and on coating on internal threads.

The component is produced; the press process stays with the customer

SUNHY’s scope is the made-to-print element. Advice may be needed so that the printed geometry can actually be produced and inspected, but the piercing process, the press load and the finished joint remain the customer’s process unless a written agreement says otherwise. A sample that was pressed into a convenient laboratory coupon is not automatic approval of the customer’s production panel, and it is not a process sign-off for the press. Installation trials, when they are required as evidence, are confirmed per order.

Inspection of the element as drawn

Dimensional checks on the body and the pierce feature, thread and coating gauges, hardness or a mechanical check, and a first-article layout are used when the print or the order requires that evidence, not automatically in every possible form. If a particular gauge, a panel coupon, or a first-article installation check is already decided, name it. A visual check that “it looks like a pierce nut” is not a substitute for the geometry written on the print. Certificates and any EN 10204 3.1, PPAP or IMDS evidence are confirmed per order when required.

Open items and conflicts

A print that omits panel thickness or hole conditions, or that references a catalogue type without attaching the current customer drawing, is flagged. A change of pierce geometry after samples have been approved is a process and tooling change and is re-validated before serial release. Compatibility with a mating bolt class remains a customer design decision, as in the note on nut property grades.

Tooling for the element is not tooling for the customer’s press

Heading dies, punches and gauges used to produce the pierce nut are process equipment for the component. They are not the piercing die in the customer’s press, and a change of those component tools is still a process change for the nut, as in the note on cold-heading tooling. A request to “match this catalogue pierce nut” is compared with the current customer drawing; the catalogue item is not used to invent missing panel data or missing geometry.

Volume and the proposed manufacturing route also belong in the enquiry. A machined prototype body is not automatic approval of a later headed route, or the reverse, when the pierce feature, the thread and the finish must meet the print in series. Those choices are stated in the quotation, and they are not changed after samples have been approved without a review. First-article inspection, when required, should be planned on the production-intent route, as in the note on first-article inspection.

The enquiry should also include any requirement for orientation, feeding features, or packing that supports the customer’s placement process, if those features are required. They have to be on the print if they are to be produced and inspected. A verbal request to “make it feeder-friendly” is not a dimension. Material grade, nut grade and finish remain print call-outs, and a substitution is not offered to close the RFQ, as in the note on material substitution. First-article inspection, when required, inspects the element as drawn; it is not a sign-off of the customer’s press.

What to send with the RFQ

Send the current drawing revision of the element, the material and finish specifications, and the panel or hole conditions that the print uses. If a customer standard, a first-article installation check, or a mating-bolt drawing is already available, attach it for information; it is not used to invent missing geometry on the nut. Volume belongs in the enquiry. Unspecified points will be flagged before production rather than assumed.

This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.