Pins and special shafts often travel with a fastener family even when they have no thread: dowel pins, grooved or knurled pins, hinge pins, special shafts, and short locating diameters with heads, grooves or flats. On a made-to-print order those items are quoted from the current drawing revision, not from a catalogue pin in a nearby diameter. A standard dowel designation is useful only when the print actually invokes it and the dimensions match.

SUNHY reviews these parts as turned parts, bushings and spacers and, where a headed form is used, alongside bolts, screws and studs, against the customer drawing. The notes on shank diameter and grip length, on undercuts and neck grooves and on secondary operations belong beside this one. This article looks at how a special pin or shaft should be written in an RFQ.

Diameter, length and the features on the body

A complete call-out names the diameter and its tolerance, the length, the end conditions (chamfer, radius, or a special point), and any groove, knurl, flat, head, hole or thread that the print shows. Fit class, if a standard pin fit is used, should be visible on the revision or named in an attached standard. “A dowel to suit the hole” or “a pin like last year” is not a dimension. If a hole or a bush drawing exists, it can be attached for information; it is not used to invent the pin tolerance.

Grooves, snap-ring seats, knurls and reduced sections are characteristics in their own right, with diameters, widths, positions and radii. They follow the same discipline as on a threaded fastener, as described in the notes on undercuts and on knurling and serrations. A commercial grooved-pin type is not assumed. Heads, if they are present, have a style, a diameter and a bearing face, as in the notes on head styles and on washer face and flange runout.

Process and later changes

Pins and shafts may be cut from bar, they may be headed, or they may be ground after heat treatment when the diameter and the surface require it. The choice is a process decision and is stated rather than assumed, as in the note on cold heading versus CNC. A ground sample is not approval of a later turned-only route, or the reverse. A change of groove tooling, of knurl method, or of the finishing process is a process change and is re-validated before serial release — see the notes on cold-heading tooling and on secondary operations.

A threaded end on a special shaft does not turn the part into a catalogue stud. The thread, its useful length and its runout are reviewed as on any other made-to-print fastener, as in the notes on useful thread length and on thread gauging. Likewise, a pin that looks similar to a connecting stub or an adapter is still quoted from its own print, not from a fittings catalogue.

Material, heat treatment and coating

Material grade, condition and any hardness or case-hardening requirement are taken from the print. A hardened dowel steel is not assumed, and a stainless grade is not a default. If carburizing or another case treatment is specified, the case depth and the hardness belong in the route and in the inspection plan, as described in the note on carburizing and case hardening. Certificates and any EN 10204 3.1 evidence are confirmed per order when required, as already described in the note on material grade and certificates.

Coating adds thickness to a fit diameter. If the finished, coated pin must still meet the tolerance, that condition should be stated; if the pin is to remain uncoated or is to be masked, that too should be written down. Heat-treatment distortion and any subsequent straightening or grinding are part of the agreed route, not informal shop corrections. On high-strength parts, any hydrogen-embrittlement control is named with the coating.

Inspection of a pin or a special shaft

Diameter, length, straightness, roundness, groove or knurl dimensions, and end-condition checks are used when the print or the order requires that evidence, not automatically in every possible form. If a particular gauge, a CMM layout, or a first-article measurement is already decided, name it. A micrometer check that “the diameter is close” is not a substitute for a tolerance, a straightness or a groove that is written on the print.

First-article or layout inspection, when required, should be planned on the production-intent route, including the finishing method and the coating state in which the diameter will be checked. Measuring a soft, fully machined sample and treating the result as approval of a heat-treated, ground and coated series part is a category error. That rule is the same as in the note on first-article inspection.

What to write in the RFQ

Quote the diameter and tolerance, the length, the ends, any groove, knurl, head or thread, the material and condition, any hardness or case requirement, the finish, any after-coating condition, the volume and the documents you need, all as they appear on the current revision. If a mating-hole drawing or a referenced pin standard exists, attach or name it. Send the print with the request form.

Send the print. The scope is confirmed before quote.

Email the current drawing revision, or use the request form. Unspecified points will be flagged before production rather than assumed.

This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.