Many made-to-print fasteners and turned parts are not finished in a single operation. A headed blank may be drilled, pointed, grooved, machined on a special face, or given a patch or a stamp. A turned part may pick up a secondary mill, a cross-hole or a separate thread. Those steps are part of the agreed route. They are not informal extras added after a quotation has been issued, and they are not omitted because they look minor on the print.

SUNHY reviews secondary operations on bolts, screws and studs, on turned parts, bushings and spacers, and on some special nuts, against the current drawing. The notes on cold heading versus CNC and on rolled versus cut threads describe the main process choice. This note is about the operations that sit around that choice.

If it is on the print, it is in the route

A cross-hole, a split pin hole, a dog point or chamfer, a groove for a ring, a machined washer face, a reduced shank, a slot, or a special stamp is a drawing feature. If it is present on the revision that is quoted, the route has to include a method for producing it and, when specified, a method for inspecting it. “We will add the hole later” is not a plan, and a heading route that cannot form the feature has to be combined with machining or replaced by a different route.

The same rule applies to gas-equipment components that need a secondary feature on a stub, an adapter or a closing element: the feature is not dropped because the main thread and hex are already defined. Each characteristic on the print belongs in the review.

Patches, adhesives and applied locking features

A pre-applied thread-locking patch, a sealant, or another applied locking or sealing feature is a specified finish, not a courtesy. The type, the colour if the specification uses colour as an identifier, the coverage and the position on the thread have to be taken from the print or the referenced standard. A patch is not substituted for a prevailing-torque nut, or the reverse, to close a gap in the enquiry. Related locking nuts are covered in the note on prevailing-torque and lock nuts.

Applied features also have process limits: curing, cleanliness, and the condition of the thread before application. If the thread must still gauge after the patch, or if gauging is only required before it, say so. Informal oil or a transit grease on top of a specified patch is not assumed.

Sequence, coating and inspection

The sequence of heading or turning, secondary machining, heat treatment, coating and any applied feature has to be planned. A hole may need to be drilled before or after heat treatment; a point may need to be cut before coating; a patch almost always comes after coating. That sequence is part of the process and is not rearranged on the shop floor to suit a machine queue.

Inspection follows the features that were added. A hole has a diameter and a position; a point has a length and an angle; a patch has a coverage or a presence check when the order requires it. These checks are included as specified, not automatically in every possible form.

A change of secondary operations is a process change

Adding, removing or moving a secondary operation after samples have been approved is a process change. So is a change from forming a feature in the heading die to machining it afterwards, or the reverse. The change is re-validated before serial release, as described in the notes on prototype samples and series production and on cold-heading tooling.

A quotation that was issued against a print without the feature does not cover a later revision that adds it. The new revision is reviewed, as in the note on drawing revision control.

Burrs, cleanliness and the features that must remain intact

Secondary machining introduces burrs, chips and handling marks that the print may or may not allow. A sealing face, a thread start, a bearing face or a weld projection has to remain inside the drawing after the extra operation. Deburr and washing are therefore part of the route when the feature requires them, not optional tidy-up. If a cleanliness or a burr specification is already written, it is followed; if it is not, a process choice that would damage a controlled face is still not acceptable.

Fixtures and workholding for a secondary operation must not erase a dimension that was already produced. A vice mark on a finished shank, or a gripping groove on a sealing diameter, is a nonconformance if the print does not allow it. Those risks are considered when the route is proposed, especially on turned gas-equipment parts and on headed fasteners that return to a machine for a hole or a special face. The quotation can mention a holding method when it affects a visible or a functional surface; it will not leave that risk implicit.

What to write in the RFQ

Point out secondary features on the current revision — holes, points, grooves, machining, patches, stamps — and say any sequence or inspection rule that is already decided. Include material, property class, finish, volume and the documents you need. Send the drawing with the request form or to anna@sunhyings.com. A wider list of enquiry items is in what to include in a made-to-print RFQ.

This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.