On a made-to-print fastener, whether the thread is rolled or cut is a process decision, not a shop-floor default. The current drawing revision, the material, the property class and the volume all influence the route. A catalogue description such as “rolled thread” does not replace what is written on that revision, and a route that was used on a similar item is not automatically reused.

SUNHY reviews this choice on bolts, screws and studs, on weld nuts and special nuts, and on threaded gas-equipment accessories, against the customer drawing. The note on thread standards, pitch and gauging covers the call-out and the gauging condition. This note is about how the thread is produced.

Rolling is common, but it is not assumed

Thread rolling is often proposed for external threads in the heading window — typically M4–M24 on the automotive fastener side of this site — because it can be combined with cold heading and supports a stable serial route. That is a starting point for review, not a commitment. Geometry, under-head features, a special pitch, a left-hand thread, or a material and property class that do not suit rolling can all point toward a cut thread, or toward a combined route.

A rolled thread also has to leave enough material and access for the dies. If the drawing shows a thread that starts against a shoulder, a short useful length, a thin wall, or a form that the dies cannot reach, rolling may not be practicable even when the diameter sits inside the usual window. Those limits are identified in the review, not discovered after tools are cut.

Cut threads, and mixed routes

A cut thread — by chasing, milling or single-point turning — is the usual starting point on many CNC-turned parts, on some larger or special-pitch items, and wherever the blank cannot be presented to rolling dies. Internal threads on nuts, union nuts and other components are a separate decision: they may be tapped, formed or machined, again as the print and the volume allow.

It is also common for one part to use more than one method. A headed blank may be rolled on the main thread and then machined on a special feature; a turned part may have a cut thread on one end and a rolled thread on the other if that is what the revision requires and the route can support it. A mixed route is written into the process. A later change from rolling to cutting, or the reverse, is a process change. It is re-validated before serial release, in the same sense as the note on going from prototype samples to series production.

What the method does and does not decide

The method of producing the thread does not change the class of fit or the gauging condition on the print. A 6g external thread, or a 6H internal thread, still has to be gauged as specified, including after coating when that is required. Rolling is not a reason to loosen the class, and cutting is not a reason to tighten it.

Surface condition, root form and runout can differ between a rolled and a cut thread. If the drawing or the referenced specification calls up a particular root radius, a measured pitch diameter, or a limitation on tool marks, that requirement belongs in the RFQ so that the method can be chosen to meet it. If the print is silent on the method, the proposed route will be stated in the quotation rather than left implicit.

Coatings, heat treatment and the final thread

Heat treatment and coating both act on the finished thread form. A thread that will be heat-treated after rolling or cutting, or coated and then gauged, has to be planned with those steps in view. Over- or under-cutting the thread “to make plating work” is not an informal shop practice; it is a process decision that must follow the print and be agreed before serial release. On high-strength parts, the coating system and any hydrogen-embrittlement control should be named with the thread requirement — see coatings for high-strength fasteners.

If only the uncoated thread is to be gauged, or if rolled and cut features on the same part have different acceptance methods, say so. The inspection plan follows those statements.

Volume, gauges and how the choice is quoted

Volume matters, but it does not override the print. A low-volume or prototype lot is often cut because the die investment for rolling is not yet justified; a later series lot may be rolled if the geometry allows it. That transition is a process change and has to be planned, with a further layout if the customer requires one. The reverse also occurs: a rolled route may be abandoned for cutting if a revision adds a shoulder, a special pitch or a thread that the dies cannot reach. Neither change is made only to fill a machine.

Rolling dies and thread gauges are part of the process equipment. If a special pitch or a non-standard form requires gauges that are not already held, that need should be visible in the enquiry so that it can be confirmed with the quotation. A method will not be chosen simply because a gauge for a more common thread is already on the shelf. The proposed method, and any open point about gauges, will be written into the quotation rather than left as a shop-floor preference.

What to write in the RFQ

If the drawing already requires a rolled or a cut thread, quote that wording and send the current revision. If the method is not stated, it helps to say whether you have a preference, or whether the route can be proposed against the print, the material, the property class and the volume. Include the thread system, size, pitch, class of fit and the final gauging condition, including after coating if that is required. Send the drawing with the request form or to anna@sunhyings.com. A wider list of enquiry items is in what to include in a made-to-print RFQ.

This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.