Knurls, serrations, ribs, flutes and similar grip or drive features appear on many made-to-print fasteners: on a thumb-screw head, on a press-in shank, on a prevailing-torque element, or on a special nut that has to lock in a stamped hole. Those features are produced to the current revision when the print states them. They are not completed from a “normal commercial knurl” once the diameter has been agreed, and they are not an unstated extra that can be added because a similar part looks better with one.
SUNHY reviews these features on bolts, screws and studs, on special nuts and on turned parts, against the customer drawing. The notes on drive recesses and socket gauging, on prevailing-torque lock nuts and on secondary operations belong beside this one. This article looks at how knurls and serrations should be written so that they can be tooled, produced and, when specified, inspected.
The feature has to be specified, not implied
A complete call-out names the type of knurl or serration, the pitch or number of teeth, the diameter before and after the feature when that matters, the length or the axial position, and any angle, depth or pattern (straight, diamond, helical, or a special form). “Light knurl” or “serrated as usual” is not a dimension. If a standard designation is used, the enquiry should say which edition applies when the print itself does not. A knurl that is only visible on a photograph, or that was added on a previous informal sample, is not a requirement until it is on the revision that is quoted.
Some features are functional: a serration that bites a sheet, a knurl that is later over-moulded, or a rib that sets a press-in load. Some are only for grip in the hand or for identification. The print, not a catalogue intent, decides which checks apply. If a press-in load, a pattern depth after coating, or a visual standard is already chosen, it should be named in the RFQ rather than left as a later surprise.
Process and sequence
Knurls and serrations can be formed in a heading die, rolled as a secondary operation, cut, or broached. The choice is a process decision and is stated rather than assumed. A feature that is rolled after heat treatment is a different route from one that is formed in the blank and then hardened; the diameter, the sharpness and the inspection condition will not be the same. A change of method, or a move of the operation in the sequence, is a process change and is re-validated before serial release — see the notes on cold-heading tooling and on secondary operations.
Weld projections, clinch features and installation ribs are related but are not the same as a decorative knurl. Their geometry and any weld or press requirement stay with the print, as already described in the notes on weld-nut projections and on clinch nuts and rivet nuts. One family is not used to invent a feature on the other.
Coating, hardness and the finished condition
A thick coating fills a fine knurl and can change both appearance and function. If the feature must remain sharp, or must meet a diameter, after coating, that condition has to be written down. Knurling after coating is a different process, with its own risk of damage to the finish, and is used only when the agreed route includes it. Informal re-knurling “to make it look right” after plating is not a made-to-print practice.
Hardness and heat treatment change how a knurl or a serration can be formed and how it will wear or bite in service. The specified material, condition and property class remain with the print, as in the notes on heat treatment and on property classes. On high-strength parts, coating and any hydrogen-embrittlement control are named requirements, not informal extras.
Inspection of the pattern
Diameter over the knurl, pitch or tooth count, length, visual appearance, or a functional press or torque check are used when the print or the order requires that evidence, not automatically in every possible form. If a particular gauge, a visual standard, or a first-article photograph is already decided, name it. A visual check that “there is a knurl” is not a substitute for a pitch or a diameter that is written on the print.
First-article or layout inspection, when required, should be planned on the production-intent route, including the coating state in which the feature will be checked. Measuring a soft, uncoated sample and treating the result as approval of a hardened and coated series part is a category error. That rule is the same as in the note on first-article inspection.
Volume, the starting material and the proposed method also belong in the enquiry. A knurl that can be cut on a prototype may be intended for rolling or for a heading die in series, and the diameter after the feature will not be the same in every method. Those choices are stated in the quotation, and they are not changed after samples have been approved without a review. The current drawing revision remains the source of the feature in every case.
What to write in the RFQ
Name the knurl or serration, include the controlling dimensions and any after-coating or functional requirement, and quote the rest of the part — thread, material, property class, finish, volume and the documents you need — as they appear on the current revision. If a visual standard or a mating-sheet drawing exists, attach it. Send the print with the request form.
Send the print. The scope is confirmed before quote.
Email the current drawing revision, or use the request form. Unspecified points will be flagged before production rather than assumed.
This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.