The material grade on a made-to-print part is the grade written on the current drawing revision, or in the specification that the drawing invokes. The certificate that travels with the order, when a certificate is required, has to match that grade. A neighbouring grade, a “commercial equivalent”, or a material that happens to be on hand is not offered in order to close an RFQ, and it is not used in production unless the customer changes the print or issues a written deviation.

SUNHY reviews the stated grade on automotive fasteners and on gas-equipment components against the drawing. The tables on the quality page list examples that are commonly reviewed — carbon and alloy steels such as 1010, 1018, 10B21, 35CrMo / 42CrMo, SCM435, and S355J2 / S355J2+N for certain fittings; stainless 304 (A2), 316 (A4) and 410; brasses including CW614N, CuZn39Pb3, CuZn40Pb2 and CuZn36Pb2; aluminium such as EN AW-6060 T6. Those are examples, not a closed stock list, and not a preference that overrides the print.

The grade and the certificate have to tell the same story

If the print states S355J2, the certificate is for S355J2, not for a generic “structural steel”. If it states 10B21, or CW614N, or 316 (A4), the same rule applies. Designations that look similar — a related brass, a different deoxidation condition, a stainless with a different condition — are different grades until the customer says otherwise in writing.

Where a print uses a standard designation and a commercial name, or a legacy grade and a current equivalent, the enquiry should say which one is authoritative. Conflicts between the purchase order and the title block are flagged, not resolved by picking the easier certificate. The note on drawing revision control covers that kind of conflict more generally.

EN 10204 3.1 and other documents are confirmed per order

EN 10204 3.1 is the document most often requested on this site. It is included when the order requires it, not automatically on every line. The certificate is issued for the lot that is supplied, and it is not relabelled from a different lot. Inspection records, a heat-treatment record, or an IMDS entry, when they are required, have to be consistent with the same grade and the same lot. The existing note on documents that can be confirmed per order sets out that rule.

A quality-system certificate is not a material certificate, and ISO 9001 is not presented as evidence of a grade. Entity, site, scope and validity are confirmed before any quality-system certificate is cited.

Property class, condition and substitution

A property class such as 8.8, 10.9 or 12.9 is not a material grade. The starting steel and the heat-treatment route have to be capable of reaching the class, but the class does not authorise a silent change of the stated steel. The notes on property classes and on heat treatment keep those ideas separate.

Requests to substitute a grade in order to shorten a lead time, to use a leftover heat, or to “approximate” a brass or a stainless are not accepted as a quotation shortcut. If a substitute is technically interesting, it is proposed only as a change the customer would have to approve on the print. Until then, the specified grade stands.

Positive identification and gas-equipment examples

If the order requires a spectrometric or other positive identification check in addition to the mill or 3.1 certificate, that check is added to the plan. A certificate alone may not replace it. The method and the acceptance rule should be stated.

On gas-equipment components, the examples already used on this site — CW614N on many brass accessories, S355J2 on many steel stubs and adapters, EN AW-6060 T6 on some aluminium housings — remain examples. The print for the item decides the alloy, as developed in materials and finishes on European gas-equipment prints.

Heats, partial lots and remaining material

A lot of parts may come from one heat or from more than one, depending on the volume and the agreement. If the customer requires a single-heat shipment, or a certificate that lists every heat in a mixed lot, that rule should be stated. It is not assumed. Remaining material from a previous order is used on a new order only when it is the specified grade and when the traceability rule for the new order is still satisfied. Leftover steel in a similar grade is not a substitute.

Partial deliveries and call-offs have to keep the certificate in step with the pieces that actually move. A 3.1 document covering a large heat is not automatically enough if the customer also requires a link to the boxes on a particular call-off. Those details are confirmed when the documents are agreed, together with packing and identification, as in the note on packing, labelling and lot traceability. They are not reconstructed after despatch from an incomplete file.

What to write in the RFQ

Quote the material grade as it appears on the current revision, and state the certificate or any additional identification you need, each confirmed per order. If two documents disagree, point that out. Send the drawing with the request form or to anna@sunhyings.com. A wider list of enquiry items is in what to include in a made-to-print RFQ.

This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.