When a European or US OEM or Tier buyer sends a made-to-print fastener drawing, one of the first questions on the supplier side is how the part will actually be made. Cold heading, CNC machining, or a combination of the two can all be legitimate answers. The right answer depends on the geometry, the specified properties and the intended volume. It should be proposed before tooling is committed, and it should be written down, because a change of route later is not a paperwork detail — it is a process change that has to be re-validated before serial release.

This article explains how SUNHY reviews that choice for automotive fasteners such as weld nuts, special nuts, bolts, screws, studs and pins, and turned parts, bushings and spacers. It is a capability note, not a promise that every geometry will be headed, or that every prototype will later be transferred to a heading line.

The M4–M24 window, and what sits outside it

Cold heading is the usual starting point inside the M4–M24 window when the form can be produced that way. That window is the typical range used in SUNHY’s automotive and gas-equipment catalogues. It is not a hard plant limit, and it is not a claim that every M4–M24 part will be headed. Forms that exceed the window, or that are not suitable for heading — deep undercuts, thin walls, certain internal features, or shapes that cannot be formed without cracking or excessive flash — are reviewed for CNC or a combined route.

A wider coverage, including sizes discussed in a general fastener range, may be reviewed by enquiry. The review still starts from the current drawing, not from a catalogue assumption.

When CNC is the better starting point

A fully machined route is used for prototypes and for parts that will remain on CNC in production. It is also the usual starting point for many rotationally symmetric parts whose concentricity, runout, bore or surface-finish limits are tighter than a headed route can reasonably hold, and for complex internals and housings on the gas-equipment side of the business.

The plant in Wenzhou covers 20,000 m² and operates 200+ CNC machines. Turning, milling, drilling and threading are used for secondary features and for precision turned parts. 5-axis equipment is applied where the geometry requires it. That capacity does not mean every part is machined in five axes, or that machining is automatically cheaper or faster than heading. It means the route can be chosen, rather than forced.

Combined routes, and secondary operations

Secondary CNC is added for features that cannot be formed, or for sizes and shapes outside the heading window. A weld nut, a special lock nut or a stud may be headed for the body and then machined for a recess, a pilot, a non-standard under-head radius or a thread that has to be cut rather than rolled. The split is part of the process definition. Tooling — heading dies, gauges and any secondary fixtures — is prepared once the route and the critical characteristics are agreed. Tooling is treated as part of the process, not as a separate afterthought.

Where a part is currently produced entirely by machining, SUNHY can review whether the geometry can be converted, in whole or in part, to cold heading. The review considers formability, tool cost, annual volume, property class, and any feature that must remain machined. The outcome is a recommendation for the enquiry, not a promised cost reduction. Savings depend on the part, the volume and the accepted process change, and they are only realised if the production-intent route is re-validated.

Prototypes are not a free pass to change the route later

Samples can be machined for dimensional and assembly validation before production tooling is committed. If the production-intent route is already defined, samples can be taken from that route. 100-piece samples are typically available in 45 days; the window is confirmed with each enquiry. For custom turned or special cold-forged nuts, typical minimum quantities in series are 10,000 to 50,000 pieces, depending on complexity and tooling. Smaller prototype lots can be machined for validation.

Approval of a prototype is not approval of the production process, unless the production-intent route has been confirmed — including forming method, tooling, heat treatment, coating and the inspection plan. If a first sample is machined and later lots are to be cold-headed, that change of route is identified and re-validated before serial release. Mixing a machined prototype with a headed production lot without that step is exactly the kind of ambiguity that a supplier-quality engineer is right to refuse.

What to write in the RFQ

If a process constraint has already been decided, state it. If it has not, send the current 2D revision, the volume and the specified properties, and the route will be proposed before tooling is committed. Include the final thread and coating condition, because gauging after coating can affect whether a thread is rolled, cut or chased. The quotation will address manufacturability, the proposed route, sample timing and the document package. See what to include in a made-to-print RFQ and from drawing to production.

Enquiries are handled in English at anna@sunhyings.com, or through the request form.

This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.