The unthreaded shank of a made-to-print bolt or screw is a functional region when the print states it. Grip length, body diameter, the transition into the thread and any reduced or enlarged diameter have to be taken from the current revision. They are not completed from a “standard shank” once the thread and the overall length have been agreed, and a commercial pitch-diameter shank is not a substitute for a body diameter that is written on the drawing.
SUNHY reviews this geometry on bolts, screws and studs and on related turned parts, against the customer drawing. The notes on useful thread length, on thread runout and on shoulder screws and precision shanks belong beside this one. This article looks at grip and body diameter as drawing characteristics, and at how they should be written in an RFQ.
Grip, body and overall length are different numbers
Overall length, thread length, useful thread, shank length and grip length are not interchangeable. A print may dimension the grip as the unthreaded length under the head, as a length that must sit in a particular joint, or as a body diameter over a stated length. Those call-outs are reviewed as written. “Long enough to clamp the joint” or “standard grip for this size” is not a dimension. If a customer standard that defines grip already exists, it should be named on the revision or attached to the enquiry.
Body diameter may be full-size, reduced, or enlarged relative to the thread. A reduced shank, a waisted body or a precision shoulder is a characteristic in its own right, with a tolerance and, when specified, a surface condition and a concentricity or runout to the thread or the head. A heading process that leaves a natural body close to the pitch diameter is acceptable only when that result sits inside the print. It is not a licence to ignore a tighter or a different diameter that is written on the drawing.
The transition into the thread
Where the shank meets the thread there is usually a runout, a neck, an undercut or a fillet. Those features occupy length and can affect fatigue and assembly. They have to be consistent with the grip and with any under-head radius. A thread that is required to start at a sharp shoulder, or a shank that must remain full diameter up to the first complete thread, may need a process that the heading die alone cannot provide. That conflict is flagged, not resolved by an informal undercut. The related geometry is discussed in the notes on undercuts and neck grooves and on under-head radius and bearing face.
Rolling a thread on a full-size shank leaves a different transition from cutting a thread down from a larger body, or from rolling after a reduced blank has been headed. The method is a process decision and is stated rather than assumed, as in the note on rolled versus cut threads. A change of transition after samples have been approved is a process change and is re-validated before serial release.
Shoulders, tight diameters and turned routes
When the shank is a locating diameter — a shoulder screw, a precision body, or a diameter that must fit a hole — the tolerance, the length and any concentricity belong on the revision and in the inspection plan when specified. A commercial shoulder-screw catalogue item is not a substitute for those dimensions. Secondary turning, grinding or a fully machined route may be required; that choice is part of the quotation, as described in the notes on cold heading versus CNC and on secondary operations.
Heat treatment can move a long or a thin shank. Straightening, if it is used, is part of the agreed route, not an informal shop correction after hardness has been checked. Coating adds thickness to a body diameter as well as to a thread; if a fit has to be met after coating, that condition should be stated. Those process-condition rules are the same as in the notes on heat treatment and on coatings already published on the site.
Inspection of the shank
Diameter, length, straightness, runout or a layout of the transition are used when the print or the order requires that evidence, not automatically in every possible form. If a particular gauge, a CMM layout, or a first-article measurement of grip and body is already decided, name it. A visual check that “there is a shank” is not a substitute for a diameter that is written on the print. Hardness and tensile checks, when required, have a location; the shank, the thread and under the head can give different information, and the specified location should be followed.
First-article or layout inspection, when required, should be planned on the production-intent route, including the method used to produce the shank and the coating state in which diameters will be checked. Measuring a soft, fully machined sample and treating the result as approval of a headed, heat-treated and coated series part is a category error. That rule is the same as in the note on first-article inspection.
What to write in the RFQ
Quote the overall length, the useful thread, the grip or unthreaded length, the body diameter and tolerance, the transition or neck, and any after-coating condition, all as they appear on the current revision. Include material, property class, finish, volume and the documents you need. If a mating hole or clamp stack exists, attach that drawing for information. Send the print with the request form.
Send the print. The scope is confirmed before quote.
Email the current drawing revision, or use the request form. Unspecified points will be flagged before production rather than assumed.
This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.