Many made-to-print fasteners and gas-equipment components include an O-ring groove or another seal gland: a turned recess, a face groove, a dovetail, or a similar form that will later hold a seal. The groove diameter, width, depth, radii and finish are characteristics of the component drawing. The seal itself is supplied only if the drawing or the order includes it. Machining a correct gland does not make the part a complete regulator, valve, filter or station, and it is not evidence that a sealed assembly has been approved.

What has to be visible on the revision

A complete call-out shows the groove diameters or widths, the depth, the radii or chamfers at the corners, the finish, and the position of the gland relative to a face, a thread or a bore. If a standard groove for a named O-ring size is intended, the standard and the size should be cited, and the drawn figures should be consistent with it. “O-ring groove, usual size” is not complete. A type code, including any SH- example used only as an illustration, does not replace the gland dimensions.

The gland is a different characteristic from a sealing face or from the bore it may sit in. Those features are discussed in the notes on sealing faces on connecting stubs and on bore and passage tolerances. Concentricity of the groove with a thread or a seat is included when the print states it; see the note on concentricity of threads and seats.

Finish and edge condition

Roughness in the groove, and the condition of the edges that the seal will pass, are taken from the revision. A scratch, a turning mark that cuts the sealing line, or a sharp corner that will nip an O-ring can be out of specification even when the width and depth are inside tolerance. If a maximum edge break or a prohibition on burrs is already defined, it is inspected as written. Dressing the edges after a failed visual check is not a substitute for a process that produces the specified radii.

Lead-in chamfers that allow the seal to be installed, and undercuts that are only a tool-clearance, should be distinguished on the drawing. A generous undocumented chamfer can reduce the land that retains the ring. Those details are not “improved” on the machine to make assembly easier.

Seals are not assumed to be in the scope

O-rings, gaskets, back-up rings and similar items are included only when they are on the drawing or on the written order. An enquiry that shows a groove is not, by itself, an order for the seal. If the customer wants the component shipped with a fitted or a loose seal, that requirement, the seal specification and the packing method have to be stated. Material of the seal, when it is in scope, is taken from the customer specification, not from a default elastomer chosen here.

Material of the component and the groove

The component material — brass, steel, aluminium or another specified grade — stays with the print, as in the notes on materials and finishes on gas-equipment prints and on aluminium components made to print. A coating or an anodising that builds in the groove is reviewed against the width and depth; a gland that must remain uncoated is masked only when the print or the order says so. Certificates and any EN 10204 3.1 evidence are confirmed per order when required.

Route, inspection and first article

The groove is produced on the agreed route, usually as part of the turning or milling sequence. A change of tool radius or of the operation that forms the corners is a process change if it can alter the gland. Width, depth, diameters, radii, finish and position are inspected as specified. A “the sample ring fits” check is useful only when the ring is a controlled gauge and the method is agreed; it is not a substitute for the groove dimensions. First-article inspection, when required, follows the note on first-article inspection.

Conflicts, volume and packing

A print that names an O-ring size and a groove that cannot contain it, or that shows two different widths for the same gland, is flagged. A general standard note and a detailed groove that conflict are reviewed together; one is not used to overwrite the other on the machine. Those conflicts are resolved on the revision, not by “easing” a width after a sample ring has been tried in the shop. If several glands appear on one part, each is inspected as specified; a correct face groove is not evidence that a piston groove on the same part has been met.

Volume and the proposed route belong in the enquiry. A form tool used in series and a prototyping groove cut with a small radius do not always leave the same corners. Packing that protects a gland, or that includes a fitted seal only when that seal is in scope, is agreed as in the note on packing, labelling and lot traceability. The part remains a component; a correct groove is not a tightness test of a complete device.

What to send with the RFQ

Send the current drawing revision with complete gland dimensions and finish, together with the component material, finish and volume. If a seal is to be supplied or fitted, include that specification. If a first-article layout of the groove is already required, say so. Unspecified points will be flagged before production rather than assumed.

This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.