Many stubs, adapters, housings and similar components have a thread at one end and a sealing seat, a cone, a bore or a face at the other, or on the same axis. The relationship between those features — concentricity, coaxiality, or a runout to a stated datum — is a controlled characteristic only when the print (or a standard the print names) states it. It is not added as a shop default, and it is not omitted because the part “looks concentric” on the machine. On a made-to-print order the relationship is taken from the current revision.
What has to be visible on the revision
A complete call-out names the datum, the feature control, the tolerance, and the extent of the surface to which it applies. A thread may be the datum for a seat, or a bore or a face may be the datum for a thread. Those two schemes are not interchangeable. “Keep thread and seat concentric” without a tolerance or a datum is not complete. Related geometry of the seat itself is discussed in the note on sealing faces on connecting stubs, and internal diameters in the note on bore and passage tolerances.
The same point applies to an O-ring groove or a taper that must run true to a thread. Those glands are specified in the note on O-ring grooves and seal glands; the relationship to the thread is an additional characteristic and has to appear on the revision. A type code, including any SH- example used only as an illustration, does not replace the geometric tolerance.
How the relationship is inspected
Runout or concentricity is inspected by the method the print or the order names, on the surfaces it names, with the part supported in a way that respects the datum. A bench check between centres is not the same as a check on a threaded arbor, and a check of a seat is not a check of a thread pitch diameter. If a particular arbor, a circular-runout versus a total-runout interpretation, or a first-article layout is already decided, it should be named. Thread gauging of the thread as a feature remains a separate check, as in the note on thread standards, pitch and gauging.
Holding the part for the measurement must not distort a thin wall or a long stub. If a special fixture is needed, it belongs in the agreed inspection plan rather than being improvised at first article. Certificates and any EN 10204 3.1 evidence of the geometric check are confirmed per order when required.
Route has to support the tolerance
A relationship between a thread and a seat is usually produced by completing both features in one setup, or by a defined sequence of operations and datums. The route is agreed. A prototype that was finished in a single chucking does not by itself approve a later route that recuts the thread in a second operation, if that change can move the relationship. Secondary operations, when they are used, follow the discipline in the note on secondary operations.
For hex-bar or cast-blank parts, the way the blank is located affects the result. Machining of a cast union-nut blank, for example, still has to respect any relationship the nut print controls, as in the note on machining of cast union-nut blanks. A change of location method is a process change.
What the relationship does not claim
A seat that runs true to a thread is still a component characteristic. It is not a leak test of a regulator, a tightness test of a station, or a PED or type-approval mark. If a pressure or tightness check on the part is required in addition to the geometric tolerance, that check is named separately. The part remains an accessory or an internal, not a complete device, in the same scope as other gas-equipment component parts.
Conflicts and open items
A print that tightens runout beyond what the datum scheme can support, or that mixes two conflicting datums on the same face, is flagged. A title-block general note and a specific feature-control frame are reviewed together; one is not used to overwrite the other on the shop floor. Those conflicts are resolved on the revision or in a written order comment.
Volume and incomplete enquiries
Volume belongs in the enquiry because the number of operations, the workholding and the machine that will hold the relationship in series may not be the ones used for a handful of prototypes. A short lot finished in a collet on a tool-room lathe does not automatically represent a later production chucking. Those differences are stated, and first-article inspection, when required, should be planned on the production-intent route, as in the note on first-article inspection.
An enquiry that only says “threads and seats must be in line” is incomplete. The datum, the tolerance and the surfaces have to appear on the revision. If the part also carries a hex, a port or a mark, those features are clocked only when the print controls them; they are not used as informal datums in place of the stated scheme. Related orientation comments are in the note on inlet-stub orientation and length. Unspecified relationships are flagged rather than given a default runout.
What to send with the RFQ
Send the current drawing revision with the geometric tolerances visible, together with the material, finish and volume. If a particular datum scheme, a gauge, or a first-article layout of the relationship is already required, say so. Unspecified points will be flagged before production rather than assumed.
This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.