European manufacturers of gas pressure regulators, filters and regulating-metering stations often buy connecting stubs and union nuts as accessories, not as a catalogue coupling set. The geometry is application-specific: a thread, a sealing face, a length and a hex or flange that have to match the equipment print. This article describes how those parts are reviewed at SUNHY, using the capability examples in the 2026 gas-equipment catalogue. It is not a stock list and not a dimensional data book.
SUNHY does not manufacture complete regulators, filters or stations. The parts discussed here are component parts, produced from the customer’s current drawing, material specification and quality requirements.
Brass inlet stubs and connecting stubs
Brass stubs and inlet nipples are produced to the customer’s drawing, in the specified material and finish. The catalogue shows two examples, both in CW614N with a natural, as-machined finish and a G 3/4 thread. SH-BR-IS-034 is an inlet stub or union nipple for regulator or station equipment. SH-BR-CS-034 is a connecting stub for equipment piping interfaces, whose geometry, length and features follow the customer’s drawing.
Those type codes are SUNHY designations for the examples. They do not replace the customer’s item number or drawing revision. Other thread systems, lengths and sealing features are reviewed from the print, not assumed from the example. Temper is taken as stated on the drawing. Colour in a catalogue model does not represent the specified material or finish.
Typical use is as an accessory at a piping interface — not as a pressure-containing assembly in its own right, and not as a substitute for the equipment maker’s design responsibility.
Brass union nuts, including the cast example
Union nuts are made to the print for use in equipment assemblies. The catalogue example SH-BR-UN-034 is a brass union nut in CuZn39Pb3 or CuZn40Pb2, with a natural finish and a G 3/4 thread. The catalogue describes this example as a cast union nut. That process description belongs to the example. It is not a rule that every union nut will be cast. The route for a production part — CNC, cold heading, a combination, or casting where that is the agreed process — is selected against the geometry and the intended volume.
Hex form, thread, sealing face and any chamfer or undercut follow the agreed drawing. Grade is taken as named on the print. Alternative copper alloys are reviewed against the drawing, the process route and the required documents; they are not substituted quietly.
Steel counterparts at the same interface
The same kind of enquiry often includes steel connecting stubs or intermediate threaded pieces. Steel stubs in the catalogue are produced in S355J2 or S355J2+N, as specified, and are typically zinc plated. The examples SH-ST-CS-054A and SH-ST-CS-054B use S355J2+N and a G 5/4 (G 1¼) thread, in two geometries. The threaded adapter SH-ST-TA-034 is in S355J2, zinc plated, with a G 3/4 thread, machined or formed as the print requires. These are accessories for equipment piping interfaces, not a standard stock range.
How the route is chosen
Many turned stubs are typically assessed for CNC, or for a combined route where volume supports it. Cold heading is treated as an M4–M24 window unless a combined or fully machined route is agreed for sizes or shapes outside that window. 100-piece samples are typically available in 45 days; the window is confirmed with each enquiry. For custom turned or special cold-forged nuts, typical minimum quantities are 10,000 to 50,000 pieces, depending on complexity and tooling.
If a first sample is machined and later lots are to be cold-headed, that change of route is identified and re-validated before serial release. The inspection plan is written against the print, including any gauging after zinc plating on steel parts. EN 10204 3.1 mill test certificates and other documents are confirmed with the order scope when requested. See materials and finishes commonly specified on gas-equipment prints and inspection and documents.
Limits of supply, stated plainly
A connecting stub or a union nut is an accessory. It is not a complete regulator, coupling assembly or station, and a quotation for the component is not a quotation for an assembled, set or certified piece of gas equipment. SUNHY’s work stops at the part defined by the drawing. If the enquiry also includes a diaphragm housing, a slam-shut internal or a filter closing element, those items can be reviewed on the same request when the drawings are provided, still as components — see the gas-equipment components hub.
What to send
Send the current 2D revision and, if available, the 3D model; the specified alloy or grade and temper; the finish; the thread system and the sealing or assembly method; volume and timing; and the documents required. Unspecified points will be flagged before production rather than assumed. A short checklist is in what to include in a made-to-print RFQ.
Enquiries are handled in English. Use the request form or email anna@sunhyings.com. Shipments can be planned under FOB, CIF or DDP terms; the scope is confirmed in the offer.
This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.