Material and finish on a gas-equipment component are taken from the customer’s drawing and confirmed with the order. The grades discussed here appear as capability examples in SUNHY’s 2026 catalogue of custom-machined and cold-headed accessories for gas pressure equipment. They are not a closed list, and they are not a licence to substitute a “similar” alloy or a standard coating when the print says something else. Alternative grades are reviewed against the drawing, the process route and the required documents.

Colour in an illustrative model does not represent the specified material or the finished surface. Catalogue type codes are SUNHY designations for examples; they do not replace the customer’s item number or drawing revision.

Brasses that appear in the examples

Brass inlet stubs and connecting nipples in the catalogue, such as SH-BR-IS-034 and SH-BR-CS-034, are shown in CW614N with a natural, as-machined finish. Temper is as stated on the drawing.

Union nuts, trip elements and relief-valve stems — including SH-BR-UN-034, SH-BR-SS-TR and SH-BR-RV-01 — are shown in CuZn39Pb3 or CuZn40Pb2, again with a natural finish, grade as named on the print.

The slam-shut basket SH-BR-SS-BK is shown in CuZn36Pb2, CuZn39Pb2 or CuZn40Pb2. The catalogue is explicit that accepted alternatives are used only if agreed. That is the right default for any leaded or unleaded substitution: it is a drawing and order decision, not a shop-floor convenience.

These designations describe the examples. A buyer whose print calls up a different copper alloy, a different temper, or a restriction on leaded grades should put that requirement in the RFQ. The review will follow the print.

Carbon steels and zinc plating

Steel connecting stubs, threaded adapters and filter closing elements in the catalogue are shown in S355J2 or S355J2+N, typically zinc plated. The condition — including whether +N is required — is taken from the drawing. Examples include SH-ST-CS-054A and SH-ST-CS-054B in S355J2+N, the adapter SH-ST-TA-034 in S355J2, and the filter closing element SH-ST-FE-01 in S355J2.

Zinc plating is the finish quoted for these examples. Other finishes can be reviewed on request and are confirmed with the drawing. If the thread must be gauged after plating, or if a particular coating thickness or after-treatment is specified, that belongs in the RFQ. A catalogue photograph, even one that looks “zinc-coloured” or “bare”, is not a finish specification.

Aluminium housings

Aluminium diaphragm housings are machined from the specified grade to the current drawing. They are housings only, not complete regulators. The catalogue shows SH-AL-DH-01 in AlMgSi1 (6081) and SH-AL-DH-02 in EN AW-6060 AlMgSi T6 to EN 754-2, both with a natural, as-machined finish. Temper and product standard are as specified. Anodising or another finish is reviewed when it is called up on the print.

Route, size window and certificates

Cold heading is treated as an M4–M24 window unless a combined or fully machined route is agreed for sizes or shapes outside that window. Diaphragm housings, complex internals and many turned stubs are typically assessed for CNC, or for a combined route where volume supports it.

Material certificates and any special inspection of the finished surface are agreed with the order scope. EN 10204 3.1 mill test certificates may be requested and are confirmed per order; they are not assumed. Quality-system certificates are referenced in a quotation only after the legal entity, site, product scope and validity have been confirmed for that order. Documents confirmed per order and the quality page set out the same rule.

What this list is not

The table of examples is a map of what has already been shown as a capability, so that a buyer can see whether a print is in familiar territory. It is not a preferred-grade list, and it is not a statement that every European gas-equipment print uses these alloys. Fastener programmes on the automotive side of the same factory use a different set of materials — carbon and alloy steels, stainless grades, and sometimes brass or aluminium — always as specified. Those families are described on the automotive fastener pages and should not be mixed up with the gas-equipment examples.

SUNHY does not manufacture complete regulators, slam-shut valves, filters or stations. A material certificate for a housing, a stub or an internal is evidence for that component, to the scope agreed in the order. It is not a certificate for a finished piece of pressure equipment.

How to specify this in the RFQ

Write the grade, temper or delivery condition, and the finish, as they appear on the drawing. If a leaded-alloy restriction, a coating system, or a gauging condition after plating is already decided, say so. Do not rely on the example grade on this site as a default. Send the current revision with the request form or to anna@sunhyings.com. A wider enquiry checklist is in what to include in a made-to-print RFQ.

This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.