The surface of a steel fastener is not only a visual finish. Heat treatment, intermediate annealing, scale, machining and coating can all change the carbon condition at the surface, and some prints or referenced specifications limit that change. On a made-to-print order, decarburization and any related surface-condition requirement are taken from the current revision. They are not assumed from a general note that the part should look clean, and they are not inspected in every possible metallographic form unless the order requires that evidence.

What has to be visible on the revision

A complete call-out names the limit — total decarburization, partial decarburization, a remaining carbon depth, or a referenced method — and the location if it is not already defined by the standard. “No decarburization” without a method, or “clean surface” as a substitute for a metallographic limit, is not complete. If a customer specification or a fastener standard already defines the check, it should be named on the revision or attached to the enquiry. Appearance requirements, if they exist, stay separate from the carbon-condition requirement unless the print ties them together.

Related surface notes — scale, residual oxide, rust, or a roughness that must survive heat treatment — are reviewed as written. They are not expanded into a full decarburization programme, and a decarburization limit is not ignored because the part will later be coated. Coating covers a surface; it does not cancel a metallographic requirement that applies to the steel itself.

The whole route is in scope

Atmosphere, temperature and time in annealing, hardening and tempering can all affect decarburization, scale and surface condition. If the print or a referenced specification sets a limit, that limit applies to the whole route, including intermediate steps, not only to the final harden and temper. Subsequent quench and temper, or a specified case treatment, starts from the structure and the surface the earlier steps left behind. Those later treatments remain as specified, as in the notes on heat treatment, on annealing and on case hardening.

A change of furnace atmosphere, of annealing position, or of a shot-blast or pickle step that is used to clean scale, is a process decision and is stated rather than assumed. A sample that was produced in a protective atmosphere is not automatic approval of a later open-scale route when the print limits surface carbon. That process-change rule is the same as in the note on prototype samples and series production.

Inspection follows the specification, not a photograph

Metallographic checks, hardness surveys near the surface, or a named surface-condition inspection are used when the print or the order requires that evidence, not automatically in every possible form. If a particular method, a micro-section location, or a first-article record is already decided, name it. A visual check that “the surface looks bright” is not a substitute for a decarburization depth that is written on the print. Certificates and any EN 10204 3.1 evidence are confirmed per order when required, as in the notes on material grade and certificates.

Open items and conflicts

A print that requires a very shallow remaining-carbon depth on a route that also needs a heavy scale-cleaning step, or that mixes a case-hardening call-out with a “no carbon change” note, is flagged. Those conflicts are resolved on the revision. The starting grade has to be consistent with the treatment, as already described for carbon and alloy steels.

Coating and machining do not hide a carbon-condition limit

A later coating, a phosphate, or a light machine cut on a point or a bearing face can change what an inspector first sees. They do not cancel a decarburization or remaining-carbon limit that applies to the steel. If a surface has to be prepared for a metallographic check, that preparation should be agreed so that the specified zone is the zone that is examined. A bright turned patch on a prototype is not evidence that a headed and heat-treated series surface meets the same limit.

Volume and the proposed route also belong in the enquiry. An anneal or a harden-and-temper cycle that is comfortable on a few laboratory pieces may be intended for a different furnace and a different atmosphere in series, and the surface carbon condition will not be the same in every method. Those choices are stated in the quotation, and they are not changed after samples have been approved without a review. First-article inspection, when required, should be planned on the production-intent route, as in the note on first-article inspection.

The enquiry should also say whether a metallographic check is required on every lot, only at first article, or only when a referenced standard is invoked. A standing request for “full laboratory support” is not a method. If a particular etchant, a magnification, or a location relative to the thread or the head is already decided, it should be named so that the inspection plan can follow it. Results from a sister part, or from a previous heat-treatment route, are not reused as evidence for the current revision. Hardness surveys near the surface, when they are used as a supporting check, still have a location, as in the note on core hardness and surface hardness. Unspecified laboratory details will be flagged rather than filled from a shop habit.

What to send with the RFQ

Send the current drawing revision, the material and heat-treatment specifications, and any standard that limits decarburization or surface carbon. If a micro-section or a first-article photograph of the surface is already required, say so. Volume and the proposed heat-treatment route also belong in the enquiry, because intermediate annealing and final hardening do not always leave the same surface. Unspecified points will be flagged before production rather than assumed.

This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.