Weld-nut bodies are often described, in conversation, as square, round or D-shape. Those words are useful as a first orientation, and catalogue photographs of those families exist on this site as examples. They are not a substitute for the outline on the customer drawing. On a made-to-print order the body width across flats or the outside diameter, the thickness, the corner radii, any D-flat or cut-out, and the relationship of that outline to the thread and the weld features are taken from the current revision.
What has to be visible on the revision
A complete body call-out shows the plan outline and the thickness, with tolerances, and it locates the thread and the weld projections or the pilot in that outline. If the nut is a square with a defined corner radius, a round body with a stated diameter, or a D-shape with a flat at a given distance from the centre, those figures belong on the revision. “Square weld nut, usual size” is not complete. A type code used only as an illustration, including any SH- example, does not replace the outline.
Thickness is a characteristic of its own. A thin body intended for a restricted weld stack is not interchangeable with a thicker body from a similar family. If the underside, the top face or a washer face is controlled for flatness or roughness, that requirement is inspected as drawn. Related comments on flange and washer faces, which appear on other nut styles as well, are in the note on washer face and flange runout.
Why the outline is not taken from a catalogue family
Two nuts that are both “square” can differ in width, corner condition, height and the placement of projections. A round body can be a simple disk or a body with a reduced weld-side diameter. A D-shape can be a true flat on a otherwise round body, or a more complex cut that also serves as a feeding feature. Selecting a catalogue family “to suit” an unstated outline is not how a made-to-print RFQ is closed. The same rule is used for other special nuts in the notes on weld nuts produced from the print and on T-nuts and other special installation nuts.
If the body also carries a pilot, a notch, or a feeding flat, those features are added only when they are drawn. They are not implied by the choice of a square, round or D-shape description. Details of pilots and of feeding features are covered in the companion notes on pilots and locating features and on orientation and feeding features.
Material, class and finish still belong on the same print
Body form does not set the property class, the material grade or the coating. Those items stay with the revision and with any referenced specification, as in the notes on nut property grades and on coatings for high-strength fasteners. A familiar body outline is not used to invent a class 8 or class 10 condition, and a coating that is usual on one example is not applied to another body unless the print says so.
Route and tooling follow the agreed outline
Heading, machining, or a combination of the two can all produce a weld-nut body. The route is agreed for the order and is not changed after samples have been approved without a review. A die that produces one square width is not assumed to be acceptable for a neighbouring width. Tooling ownership and a die change are commercial and process points, as already set out in the note on cold-heading tooling.
Volume belongs in the enquiry because it affects that route. A short prototype lot can be milled from plate or bar in a way that will not be used in series. First-article inspection, when required, should be planned on the production-intent method so that the corners, the thickness and the weld-feature positions represent the serial part, as in the note on first-article inspection.
Inspection of the body
Across-flats or outside diameter, thickness, corner radii and any D-flat are inspected as specified. Position of the thread and of the weld features in the body is included when the print controls it. A “it looks like the sample” check is not a substitute for those figures. Certificates and any EN 10204 3.1 evidence are confirmed per order when required, not assumed as a blanket attachment to every body style.
Projections, pilots and the body have to agree
Weld projections, a pilot, or a feeding feature are located in the body, not beside an abstract square or round description. If the print shows four projections on a square body, their pitch and their distance from the sides are inspected with the outline, as already required in the note on weld projections and location features. A projection layout taken from a round example is not moved onto a square body to close an RFQ. The same applies to a D-flat that is also used as a weld-side clearance: the flat is produced as drawn, and it is not deepened to clear a tool that is not on the print.
Volume and packing belong in the same enquiry. A thick square body and a thin round body do not always share a packing method, and a feeding edge can be damaged if the parts are shipped loose in a bag. Those points are agreed when they are specified, as in the note on packing, labelling and lot traceability, and they do not change the body outline.
What to send with the RFQ
Send the current drawing revision, including a clear view of the body outline and thickness, together with the material, finish and volume. If a first-article layout of the body is already required, say so. Unspecified points, including an enquiry that only names “square”, “round” or “D-type” without an outline, will be flagged before production rather than assumed.
This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.