Automatic placement of a weld nut or a clinch nut often depends on a flat, a notch, a groove, a D-shape, or another feature that orients the part in a bowl, a track or a fixture. Those features are part of the component only when they are on the print. They are not added because “this type is usually fed that way”, and they are not a reason to quote the customer’s feeder, robot or press as a SUNHY assembly. On a made-to-print order orientation and feeding features are taken from the current revision.
What has to be visible on the revision
A complete call-out shows the feature, its width, depth or angle, and its position relative to the body, the thread, the weld projections or the clinch geometry. If a pair of flats, a single notch, or a cam that a hopper track must pick up is required, it is drawn. “Prepare for automatic feed” without a geometry is not complete. Body outline and locating pilots are related but separate characteristics; they are covered in the notes on square, round and D-shape weld-nut bodies and on pilots and locating features, and they do not invent a feeding notch that is not shown.
If the customer already has a feeder standard or a preferred orientation, that document should be named on the revision or attached to the enquiry. A photograph of a sample from a previous programme is useful context; it is not a substitute for dimensions on the current revision. A type code, including any SH- example used only as an illustration, does not replace the feature.
Why the feature has to be on the print before tooling is cut
A feeding flat changes the body, the heading die or the secondary milling operation. Adding it after samples have been approved is a process and tooling change, not a small courtesy. If the feature is needed, it should be on the revision used for the quotation and for first article. The same discipline is used for other heading and secondary operations in the notes on cold-heading tooling and on secondary operations.
Position relative to weld projections or to a clinch shank matters. A notch that coincides with a projection, or a flat that leaves too little bearing area, is flagged rather than “adjusted” on the die. Projection layout itself remains a drawing input, as in the note on weld projections and location features.
The feeder and the press stay with the customer unless agreed
Bowl feeders, tracks, escapements, cameras and the press or weld fixture remain the customer’s process, unless a written agreement includes a trial or a defined handling step. SUNHY quotes the nut as a component with the features that are drawn. A statement that the nut “must feed reliably” is not complete without a geometry, and it is not a performance guarantee of a feeder that is not part of the order. The same boundary is used for the customer’s press and weld processes in the notes on clinch nuts and rivet nuts and on weld nuts produced from the print.
Finish, marking and packing can affect feeding
A coating thickness, a heavy oil, a sharp burr, or a mark in the wrong place can change how a nut sits in a track. If the print requires a finish and also requires a feeding feature, both are reviewed together. Marking, when it is specified, should be located so that it does not defeat the orientation feature. Packing that is intended to protect a feeding edge, or to keep parts oriented in a tray, is included when the order says so, as in the note on packing, labelling and lot traceability. It is not assumed from a feeder conversation.
Inspection of the feature
Width, depth, angle and position of the feeding feature are inspected as specified, together with the body and the functional geometry of the nut. A “it ran in our bowl for an hour” anecdote is useful background; it is not a substitute for the dimensions unless that trial is itself the agreed method and the equipment is defined. First-article inspection, when required, should be planned on the production-intent route, as in the note on first-article inspection. Certificates and any EN 10204 3.1 evidence are confirmed per order when required.
Conflicts and volume
A print that places a feeding notch through a weld projection, or that asks for “automatic feed” on a body that has no orientation feature and no stated standard, is flagged. Two documents that clock the same flat to different projections are reviewed together; one is not used to overwrite the other on the die. Those conflicts are resolved on the revision or in a written customer decision, not during a trial on the customer’s bowl after series tooling has been cut.
Volume belongs in the enquiry. A milled notch on a short prototype lot does not by itself approve a later headed or punched feature if the width or the position will change. If several nuts in a family share a feeder but differ in thickness or in projection layout, each item number is still quoted from its own current revision. Similarity is not a licence to copy a notch from a sister part.
What to send with the RFQ
Send the current drawing revision, including any feeding or orientation feature, together with the material, finish and volume. If a feeder standard or a preferred orientation already exists, attach it. If a handling trial is already decided, say who provides the equipment. Unspecified points will be flagged before production rather than assumed.
This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.