On a coated fastener, the friction behaviour of the surface is a specified characteristic when the print or the referenced coating standard makes it one. It is not a side effect that can be left to the colour of the part or to a trade name. Coefficient of friction, a friction class, a lubrication or topcoat, and any torque-tension requirement have to be read from the current revision and from the specification it invokes.

SUNHY reviews those requirements on bolts, screws and studs and on mating nuts when they are stated. The existing note on coatings for high-strength fasteners covers the choice of system, post-coating gauging and hydrogen-embrittlement control. This note is about friction and torque-tension only. It does not repeat that hydrogen-embrittlement discussion.

Name the friction requirement, not only the coating

A zinc, zinc-nickel or zinc-flake system, including named flake systems such as Geomet or Dacromet when the print calls them up, does not by itself fix the coefficient of friction. Many specifications add a friction class, a μ range, a lubricant, a sealer or a topcoat. If that information is missing, it is an open item. It is not completed from a colour sample, from a previous lot for a different item, or from a photograph on this site.

If several friction states are possible under the same coating family — for example a dry surface, a lubricated surface, or a specified topcoat — the state that applies to the part has to be written down. “As usual” or “standard friction” is not a substitute for the class or the range on the specification.

Torque-tension is a joint requirement

A torque-tension or clamp-load requirement describes how the fastener is expected to behave in the joint. When such a requirement is on the print or in the referenced standard, it belongs in the RFQ together with the coating and the friction class. The method, the lubrication condition of the test, the mating parts and the acceptance range all matter. A shop torque check with an unspecified washer is not a substitute for a method that the standard already defines.

Torque-tension testing is included when the order requires it, not automatically on every lot. If only a coefficient-of-friction measurement is required, or only a reference to a coating-system friction class, say so. The inspection plan follows that statement rather than a general practice.

Thread condition, lubrication and additional oils

Friction and thread gauging interact. A lubricant or a wax that brings the surface into a specified μ range can also affect how a gauge feels, and a thick topcoat can affect both friction and the class of fit. The final thread condition — uncoated, coated, or coated and lubricated — should be stated, as in the note on thread standards, pitch and gauging.

An additional oil, a transit lubricant or a customer-applied grease is not assumed. If the part must ship dry, or must ship with a named lubricant and no other, that instruction belongs in the order. Informal oiling “to help assembly” is not part of a made-to-print route unless the specification allows it.

Property class and the rest of the finish

Friction requirements often appear on property classes such as 8.8, 10.9 and 12.9, but they can also appear on other fasteners and on nuts. The class, the coating system and the friction class are separate call-outs; one of them does not fill in the others. High-strength parts still need any hydrogen-embrittlement control to be named, as already described in the coatings note, alongside the friction data.

Documents that evidence the coating or the friction test are confirmed per order, in the same way as EN 10204 3.1 or an inspection record. They are not an automatic attachment. See documents that can be confirmed per order.

Mating parts, washers and the stated test condition

A friction or torque-tension result depends on the mating parts as well as on the fastener under review. If the specification requires a defined nut, washer, test plate or lubrication state, that set-up is part of the method. A result obtained on a convenient shop nut, or on a washer that the print does not mention, is not evidence against a method that already names the counterparts. When only the coating-system friction class is required, without a joint test, that narrower scope should be stated so that the plan stays inside it.

Washers, captured washers and flange heads change the bearing surface and can change the friction behaviour. If a captured washer or a special bearing face is on the fastener print, it belongs in the same review as the coating. Additional lubrication applied by the customer at the line is outside the as-supplied condition unless the order says it must be considered. The quotation will describe the as-supplied surface, not the joint after an unstated oil has been added.

What to write in the RFQ

Name the coating system, the friction class or μ range, any lubricant or topcoat, and any torque-tension or friction test, as they appear on the current revision or in the referenced specification. Include the property class, the thread and the gauging condition. Send the drawing with the request form or to anna@sunhyings.com. A wider list of enquiry items is in what to include in a made-to-print RFQ.

This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.