The thread on a made-to-print fastener does not usually run at full form from one end of the part to the other. There is a useful or complete thread, a runout or incomplete thread, and often an unthreaded shank or a neck next to the head. Those regions are drawing-controlled when the print states them. They are not a leftover of the heading die, and they are not completed from a “normal commercial runout” once the thread diameter has been agreed.
SUNHY reviews this geometry on bolts, screws and studs and on threaded features of other made-to-print parts, against the current revision. The notes on thread standards, pitch and gauging and on rolled versus cut threads cover the system, the class of fit and the method. This article looks at where the thread starts and stops, and at the incomplete thread that often sits between a full form and a plain shank.
What has to be visible on the revision
A complete call-out names the thread system, the size and the class of fit, and it also makes the useful length, any gauge length, and the runout or incomplete thread visible on the same revision. Some prints dimension a minimum full-form length; some show a maximum incomplete thread; some control both, together with a shank length or a neck. “Thread as far as possible” or “run the thread up to the head” is not a substitute for those dimensions. If the drawing is silent, the enquiry has an open item, not a licence to use a shop default.
Where the thread meets a shoulder, a under-head radius or a neck groove, the features have to be consistent with one another. A thread that is required to run close to the head may conflict with a large fillet; that conflict is flagged, not resolved by silently cutting an undercut that the print does not show. The same point is made in the notes on under-head radius and bearing face and on undercuts and neck grooves.
Runout is not a free zone
An incomplete thread or a runout still occupies length, and it still has a form. Rolling dies and cutting tools leave different runout shapes. If the print or the referenced specification limits the incomplete thread, or requires a particular runout form, that limit belongs in the review so that the method can be chosen to meet it. If the print is silent on the method, the proposed route is stated in the quotation rather than left implicit, as described in the note on rolled versus cut threads.
A runout that enters a sealing diameter, a bearing face or a weld projection is a different problem from a runout that sits on a plain shank. Those functional surfaces have to remain inside the drawing after the thread is produced. Secondary machining, if it is used to clean a start or to add a neck, is part of the agreed route, not an informal tidy-up after samples have been approved. That process-change rule is the same as in the note on secondary operations.
Gauging follows the stated length
Thread gauges read the complete thread. If a useful length, a gauge length or a stand-off is shown on the print, the inspection plan has to respect it, including after coating when that condition is required. A thread that was shortened to clear a tool, or lengthened to make gauging easier, is not a permitted adjustment. Over- or under-cutting “to make plating work” is a process decision that must follow the print, not an informal shop practice.
Internal threads on nuts and components follow the same discipline in a different geometry: a useful depth, a runout or a chip-groove, and the gauging condition are taken from the print. That subject is developed further in the note on internal threads, tapping and gauging.
Heading, machining and later changes
On a headed route, the blank length, the rollable length and the under-head features all constrain the runout. On a turned route, the programmer can often place the start more freely, but still only inside the drawing. A machined sample with a turned runout is not approval of a later rolled runout, or the reverse. A change of method, or a change that moves the incomplete thread, is a process change and is re-validated before serial release — see the notes on cold-heading tooling and on prototype samples and series production.
Heat treatment and coating also act on the finished thread form. Distortion, a thick coating or a subsequent sizing step can change how much useful thread remains and how a gauge feels. Those steps are reviewed as part of the sequence, not after the first serial lot. On high-strength parts, any hydrogen-embrittlement control is named with the coating, as already described in the existing coatings note, alongside the thread requirement.
What to write in the RFQ
Quote the thread system, size and class as they appear on the current revision, together with the useful length, any incomplete-thread or runout limit, the shank or neck, and the gauging condition, including after coating if required. Point out where the thread meets the head, a shoulder or a sealing feature. Include material, property class, finish, volume and the documents you need. Send the drawing with the request form.
Send the print. The scope is confirmed before quote.
Email the current drawing revision, or use the request form. Unspecified points will be flagged before production rather than assumed.
This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.