Relief-valve stems, spindles and related internals appear on gas-equipment prints as turned or ground components, sometimes with seats, grooves, threads or cross-holes. SUNHY quotes those items as made-to-print parts. A complete relief valve, a complete regulator, a slam-shut valve, a filter or a station is not manufactured here, and a correctly made stem is not a type test or a PED approval of those devices. The same scope is already used for other internals in the note on slam-shut valve internals sourced as components.

What has to be visible on the revision

A complete call-out shows the diameters and lengths, any sealing or seating form, threads, grooves, cross-holes, and the material and finish. If a hardness, a coating, or a geometric relationship between a seat and a diameter is required, it belongs on the same revision. “Relief-valve stem, usual size” is not complete. A type code, including any SH- example used only as an illustration, does not replace the item number and the current revision.

Related component characteristics are treated in the same way as on other accessories. A seating face follows the discipline in the note on sealing faces, a groove follows the note on O-ring grooves and seal glands, and a bore or a passage in a mating internal follows the note on bore and passage tolerances. Those articles do not convert the stem into a complete valve.

What is not included with the stem

Springs, seals, housings, seats that are separate parts, setting of a crack-off or relief pressure, and assembly of a complete valve stay with the customer, unless a written order includes a named additional component. SUNHY does not offer a set pressure, a flow, or a declaration that the stem is approved for a particular device. If two or more internals are to be shipped together, that packing arrangement is stated; it still does not create an approved valve.

Marking on the stem, when it is specified, follows the drawing. A mark is not a type-approval or a setting mark for a complete relief valve. The general rule is the same as in the note on marking on gas-equipment components.

Material, heat treatment and finish

The grade, any heat treatment or hardness, and the coating or passivation are taken from the print, not from a default “valve steel” habit. Stainless, carbon steel, brass or another specified material is quoted only when it is the grade on the revision. Common material comments for this field are in the note on materials and finishes on gas-equipment prints. Hydrogen-embrittlement relief, when it applies to a coated high-strength stem, is confirmed per order, as on other fasteners and turned parts. Certificates and any EN 10204 3.1, PPAP or IMDS evidence are likewise confirmed per order when required.

Route and inspection

Turning, grinding, threading, cross-drilling and any secondary finishing follow the agreed route. A ground prototype seat does not by itself approve a later turned seat if the roughness or the form will change. Concentricity or runout between a seat and a guiding diameter, when it is specified, is part of that route and of the inspection plan, as in the note on concentricity of threads and seats.

Diameters, lengths, seats, threads, grooves and, where specified, hardness or roughness are inspected as required. A pressure test on the loose stem is included only when the print or the order requires it, and it remains a test of the part. First-article inspection, when required, should be planned on the production-intent route, as in the note on first-article inspection.

Conflicts, packing and volume

A print that names a seat form and a hardness that conflict, or that calls for a coating on a seating diameter that must remain uncoated, is flagged. Mixed notes that describe the article as a “relief valve” in the title block and as a stem in the views are read as a component enquiry; they are not taken as a request to supply a complete valve. If the customer actually needs a complete device, that work is outside the scope of this site and is not quoted as an assembly approval. Related accessory boundaries are also stated in the note on union nuts versus threaded adapters.

Volume belongs in the enquiry, because grinding, hard turning and a simple turned finish are not interchangeable routes at every quantity, and a change of route after samples have been approved is reviewed. Packing that protects a seat, a thread or a fine diameter, when it is specified, is agreed as in the note on packing, labelling and lot traceability. Seals and springs are packed with the stem only when they are on the order. A family of stems that differ by length or by seat diameter still needs a current revision for each item number; similarity is not a licence to copy those figures from a sister part.

What to send with the RFQ

Send the current drawing revision of the stem or internal, together with the material, finish, volume and any hardness or geometric specification. If a particular certificate, a tightness check on the part, or a packing arrangement with other internals is already required, say so. Do not send only a request to “quote the relief valve”. Unspecified points will be flagged before production rather than assumed.

This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.