Union nuts and threaded adapters often appear in the same gas-equipment interface, sometimes in the same photograph, and they are sometimes requested under a single word: “the fitting”. They are different components. A union nut is typically a nut with an internal thread and a shoulder or a swivel face that retains or tightens against another part. A threaded adapter or connecting stub is typically a turned piece with external or mixed threads and a sealing or connecting form. On a made-to-print order the RFQ has to name the component, show the current revision, and stay inside the scope of component parts, not complete regulators, valves, filters or stations.

Name the component, then quote the print

The enquiry should identify whether the item is a union nut, a connecting stub, a threaded adapter, or another accessory, and it should attach the drawing for that item number. “Quote the brass fitting on the inlet” is not complete if two or more parts sit at that inlet. Existing notes on brass connecting stubs and union nuts and on steel connecting stubs and threaded adapters introduce those families; they do not allow one article to be quoted in place of the other.

Catalogue examples, including any SH- or SH-BR type used only as an illustration, are not a substitute for the item number and the revision. A cast union-nut blank, where that route is used, is still finished to the print of the nut, as discussed in the note on machining of cast union-nut blanks; it is not a stock adapter.

What belongs on each revision

For a union nut, the thread, the across-flats or other drive, the overall height, the shoulder or swivel face, and any sealing or retaining diameter have to be drawn. For an adapter or stub, the threads, the sealing faces, the bore, the length and the position of flats or ports are the usual set. Across-flats are covered in more detail in the note on hex and spanner flats, and sealing faces in the note on sealing faces on connecting stubs. Those details do not merge the two parts into one quotation line.

Material and finish stay with each print. A brass nut and a steel adapter at the same interface are two materials, two routes and two inspection plans, even if they are ordered together. Common material notes are collected under materials and finishes on gas-equipment prints. Certificates and any EN 10204 3.1 evidence are confirmed per order and per item when required.

Threads and interfaces are not a licence to redesign

Matching threads do not make the parts interchangeable. A union nut is not quoted as a substitute for a hex adapter, and a stub is not quoted as a nut with a longer body. If the customer is still choosing between two designs, both drawings should be sent and each should be quoted as itself, or the choice should be made before the production order. Pipe-thread form, where it appears, follows the note on pipe threads on gas-equipment components; it is not used to invent the rest of the outline.

What is not included

Neither component is offered as a complete regulator, slam-shut valve, filter or station, and neither quotation is a PED or type-approval of an assembly. Seals, gaskets and mating housings are supplied only if they are on the drawing or on the order. If the two parts are to be shipped as a set, that packing arrangement is stated; it still does not create an approved assembly.

Inspection and first article

Each item is inspected to its own revision. A layout of the nut does not serve as the layout of the adapter. First-article inspection, when required, is planned per item number on the production-intent route, as in the note on first-article inspection. A change of route on one of the two parts is reviewed for that part; it is not assumed to be covered because the other part did not change.

Route, volume and open items

A union nut may be produced from bar, from a heading, or from a cast blank that is later machined; an adapter is usually turned. Those routes are agreed per item and are not swapped after samples have been approved without a review. Volume belongs in the enquiry, because a short prototype lot can hide a route that will not be used in series. First-article evidence should name the item number it belongs to, so that a nut layout is not later read as approval of the adapter.

An enquiry that attaches one photograph of an assembled interface and asks for “all the fittings” is incomplete. The parts should be listed, each with a current revision. Conflicts between a nut drawing and an adapter drawing — threads that do not match, or a shoulder that cannot meet the face — are flagged. They are resolved by the customer on the revisions, not by redesigning one component in the quotation to force a fit. Pipe threads, sealing faces and flats are taken from each print, not from the photograph.

What to send with the RFQ

Send the current drawing revision for each item number, clearly named as a union nut, a stub, an adapter, or another accessory, together with material, finish and volume. If the parts are to be supplied together, say so. Unspecified points, including an enquiry that only says “the fitting”, will be flagged before production rather than assumed.

This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.