Some union nuts start as a cast blank that is then machined on the thread, the faces, the bore and any sealing or swivel diameters. That route is used only when it is appropriate to the print and agreed for the order. The blank is not a finished article, and a catalogue photograph of a cast-looking nut is not a stock item that can be shipped against a different drawing. On a made-to-print order the nut is finished and inspected to the current revision, whether the starting form is a casting, a heading, or a piece of bar.

What has to be visible on the revision

The customer drawing of the finished nut remains the authority: thread, across-flats or other drive, height, shoulder or swivel face, sealing diameters, and any geometric tolerances. If the customer also issues a blank drawing or a note that a cast blank is acceptable, that document should be attached. “Cast union nut, usual size” is not complete. The distinction between the nut and a threaded adapter at the same interface is already drawn in the note on union nuts versus threaded adapters; the presence of a casting does not blur that line.

Material of the casting, including a brass or other copper alloy named on European gas-equipment prints, has to match the finished-part specification. Common material notes are in materials and finishes on gas-equipment prints and in the article on brass connecting stubs and union nuts. A familiar SH- example used only as an illustration is not a licence to substitute a different alloy or a different outline.

The blank is part of the agreed route

Where a cast blank is used, the source of the blank, the allowance for machining, and the locations used to fixture the nut are part of the agreed route. A change of foundry, of blank revision, or of the faces used for location is a process change and is reviewed before serial use. Porosity, flash, or a shift in the as-cast hex that leaves insufficient machining stock is a blank-quality issue; it is not corrected by quietly reducing a finished diameter below the print.

A fully machined prototype taken from bar does not by itself approve a later cast-blank route, or the reverse, if the grain of the surface, the hex corners, or the internal soundness will change. First-article inspection, when required, should be planned on the production-intent route, as in the note on first-article inspection.

Machining and inspection still follow the finished print

Threads, faces and bores are machined and inspected as specified, regardless of how the blank was made. Across-flats may be used as-cast when the print allows it, or they may be machined; that choice is not assumed. If a relationship between a thread and a face is controlled, the machining sequence has to support it, as in the note on concentricity of threads and seats. Hex and spanner data, where they are machined or checked, follow the note on hex and spanner flats.

Certificates for the casting and for the finished nut, including any EN 10204 3.1 evidence, are confirmed per order when required. A foundry certificate alone may not replace a finished-part inspection or a material requirement that applies after machining. IMDS or other substance data, when requested, have to reflect the actual alloy of the blank and of any later coating.

What the route does not claim

A machined cast union nut is still a component. It is not a complete regulator, valve, filter or station, and a cast appearance is not a PED or type-approval mark. Seals and mating stubs are supplied only if they are on the order. Pressure or tightness checks, when specified, are tests of the part, not type tests of an assembly.

Open items

A print that shows a sharp internal corner the blank cannot support, or that names a material the proposed foundry route cannot meet, is flagged. Those conflicts are resolved on the revision or in a written choice of route, not on the shop floor after the blanks have arrived.

Finish, packing and volume

Any coating, passivation or cleanliness requirement applies to the finished nut, including in threads and on faces that have been machined from the cast surface. A coating that fills a thread or a face that must remain as-machined is reviewed as specified, not applied as a blanket over the raw casting. Packing that protects a machined sealing or swivel face is included when the order says so, as in the note on packing, labelling and lot traceability.

Volume belongs in the enquiry because blank tooling, foundry lead time and a bar-machined alternative are different commercial and technical routes. A very short lot may be proposed from bar even when series parts will be cast; that difference must be visible in the quotation and at first article. The nut is still quoted as a component, not as a complete fitting assembly, and a union nut and its mating stub remain separate item numbers even when they are packed together.

What to send with the RFQ

Send the current drawing revision of the finished nut, any blank drawing or route preference, and the material, finish and volume. If a first-article layout or a particular certificate for the casting is already required, say so. Unspecified points will be flagged before production rather than assumed.

This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.