A flange nut and a plain hex nut may share a thread and a property grade and still be different parts. The flange diameter, the thickness of the flange, any serrations or contact features, and the bearing-face condition are characteristics of the drawing. They are not added or removed to match a stock hex, and a captured washer is not treated as a silent substitute for an integral flange. On a made-to-print order the body style is taken from the current revision.

What has to be visible on the revision

A complete call-out shows whether the nut has a flange, the flange diameter and thickness, the hex across-flats and height, and whether the bearing face is plain, serrated, or otherwise formed. If a washer face, a chamfer, or a runout tolerance is controlled, it belongs on the same view or in a named standard. “Hex nut with flange if needed” is not complete. A type code, including any SH- example used only as an illustration, does not replace the outline.

Geometric condition of the bearing face is discussed in more detail in the existing note on washer face and flange runout. That note does not authorise a style change. A plain hex that meets a runout figure is still not a flange nut, and a flange nut is not accepted in place of a plain hex because it “covers more area”. The customer changes the print if a different style is required.

Serrations, contact features and friction

Serrations under a flange, a knurl, or a smooth bearing face are not interchangeable. They affect contact with the mating face and, where the print or a specification also names a friction class, they can belong to that conversation. Friction, torque and tension on coated fasteners are covered in the note on friction class and torque-tension; those values are used when they are specified, not invented to justify a serration pattern that the drawing does not show.

A prevailing-torque feature, a polymer insert, or a metallic lock collar can appear on either a flanged or a plain body. Those are additional characteristics, not a reason to change the flange. See the notes on prevailing-torque and lock nuts and on nylon-insert lock nuts.

Why a substitution is not a shortcut

Purchasing sometimes asks whether a plain hex plus a washer can be quoted in place of a flange nut, or whether a flange nut can be used “because it is more common”. On a made-to-print order the answer is no, unless the customer revises the drawing or issues a written concession. The washer, the contact diameter and the height of the joint are part of the customer’s design. Substituting them in the quotation would invent a different part. Captured-washer assemblies, when they are themselves the specified article, are a separate family and are described in the note on captured washers and pre-assembled fastener elements.

Material, grade and finish

Property grade, material and coating stay with the print, as in the notes on nut property grades and on coatings for high-strength fasteners. A flange is not used to infer a higher grade, and a coating that is usual on one body style is not applied to the other unless the revision says so. Certificates and any EN 10204 3.1, PPAP or IMDS evidence are confirmed per order when required.

Route, inspection and first article

Heading, machining, and any secondary facing or serrating of the flange follow the agreed route. A change from a headed flange to a machined flange, or a change of serration die, is a process change and is reviewed before serial use. Across-flats, flange diameter, height, thread, and any specified face runout or serration check are inspected as the print requires. First-article inspection, when required, should be planned on the production-intent route, as in the note on first-article inspection.

Height, wrench clearance and incomplete enquiries

Overall height and the height under the flange, where both are shown, are inspected as drawn. A flange nut is often taller than a plain hex of the same thread, and a reduced-height flange nut is a different part again. Wrench clearance around the flange, and the diameter that the flange must clear in a pocket, are customer design data; a conflict that is visible on the drawing is flagged rather than “solved” by turning the flange down. The same restraint applies to a request to add serrations to a print that shows a smooth face, or to remove them from a serrated flange.

Volume and the proposed route belong in the enquiry. A short lot can be machined from hex bar in a way that will not be used in series, and the flange diameter or the serration form may not represent the headed part. Packing that protects a serrated face, when it is required, is agreed as in the note on packing, labelling and lot traceability. An enquiry that only asks “flange or hex, same thread” is incomplete and will be flagged.

What to send with the RFQ

Send the current drawing revision with a clear view of the body and the bearing face, together with the grade, finish and volume. If a friction, serration or runout specification is already decided, include it. Do not send only a request to “quote flange or hex”. Unspecified points will be flagged before production rather than assumed.

This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.