Some made-to-print fasteners are not a single piece when they are delivered: a screw or a bolt with a captured washer, a pre-assembled washer pair, a cage, or another element that is meant to stay with the fastener in transit and in assembly. Those elements are part of the current drawing revision and of the agreed route when the print states them. They are not an unstated extra that can be added because a similar commercial SEMS screw exists, and they are not omitted because the thread and the head would already be complete without them.
SUNHY reviews the fastener and the captured element together, against the customer drawing, in the bolts, screws and studs and special nuts families. The notes on washer face and flange runout, on friction class and torque-tension and on packing, labelling and lot traceability belong beside this one. This article looks at how a pre-assembled element should be written so that it can be sourced, assembled and, when specified, inspected.
The print has to show both elements
A complete call-out identifies the fastener and the washer or cage: material, hardness or property class, dimensions, finish, and any standard or customer part number for each element. The way the washer is retained — a captured thread, a deformed shank, a flange, a cage, or a special clip — is a characteristic in its own right. “With washer” or “SEMS style” without those details is not complete. If the washer is a customer-supplied item, that fact, and the condition in which it will be received, should be visible in the enquiry.
The washer face, any serration, and the under-head geometry of the screw still have to be consistent with a free washer that can turn, or with a washer that is intended to stay in a fixed orientation. Those features follow the same discipline as on a one-piece flange, as in the notes on washer-face runout and on under-head radius and bearing face. A captured washer is not a substitute for a flange that the print actually shows, or the reverse.
Route, coating and later changes
The sequence — coat each element and then assemble, assemble and then coat, or mix those steps — changes both the finish and the fit of the capture. That sequence is part of the agreed route and is stated rather than assumed. A sample assembled from uncoated pieces is not approval of a later coated assembly, or the reverse. Adding, changing or omitting the captured element after samples have been approved is a process change and is re-validated before serial release, in the same spirit as the notes on secondary operations and on prototype samples and series production.
Friction, lubrication and any prevailing-torque or locking element on the same fastener remain print call-outs. Informal oiling of the washer face, or a change of washer hardness “to make torque work”, is not a made-to-print practice. Those points connect to the existing notes on friction class and on prevailing-torque lock nuts. On high-strength screws, any hydrogen-embrittlement control is named with the coating of the screw, and the washer finish is specified in its own right.
Retention, packing and traceability
How firmly the washer is retained, and whether it may still turn, is a requirement when the print or a referenced standard states it. A functional check — pull-off, rotation, or a similar test — is used when the order requires that evidence, not automatically in every possible form. If a particular method or a first-article check is already decided, name it. A visual check that “the washer is on” is not a substitute for a retention requirement that is written on the print.
Packing has to keep the assembly together and identifiable. Mixed lots of screws and loose washers, or a box in which washers can leave their screws, may be unacceptable even when each piece is individually correct. Labelling and lot traceability should cover the assembly as delivered, and, when specified, the lots of the elements that went into it. Those packing rules are the same as in the existing note on packing, labelling and lot traceability.
Inspection of the assembly
Dimensional checks on the screw, on the washer, and on the assembled height or capture, together with thread and drive gauging, are used when the print or the order requires that evidence. Coating-state conditions apply to each element as specified. First-article or layout inspection, when required, should be planned on the production-intent route, including the assembly and coating sequence. Measuring the screw alone and treating the result as approval of the assembled part is a category error. That rule is the same as in the note on first-article inspection.
Certificates and any EN 10204 3.1, PPAP or IMDS evidence are confirmed per order when required. If the washer and the screw need separate material evidence, that should be stated in the RFQ rather than left to a later assumption. The existing notes on material grade and certificates and on order documents apply to each element as well as to the assembly.
What to write in the RFQ
Identify the fastener and the captured element, including material, finish, dimensions and any part numbers, together with the method of retention, the coating and assembly sequence if it is already decided, the volume and the documents you need, all as they appear on the current revision. If a washer standard or a customer-supplied element is involved, say so. Send the print with the request form.
Send the print. The scope is confirmed before quote.
Email the current drawing revision, or use the request form. Unspecified points will be flagged before production rather than assumed.
This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.