Cap nuts, dome nuts and various security or anti-tamper nuts are special nuts whose closed end, dome height, drive form and internal thread depth are taken from the drawing. Catalogue photographs and example type codes on this site, including any SH- cap-nut illustrations, show the kind of work that can be discussed. They are not a stock list and they are not a licence to finish a different dome because it is “close enough”. On a made-to-print order the form is produced to the current revision.
What has to be visible on the revision
A complete call-out shows the external form — a full dome, a high cap, a low cap, a flange cap, or another drawn shape — together with the height, the across-flats or other drive, and the useful internal thread. If the closed end is a formed dome, a fused cap, or a machined cover, that construction should be clear, or the enquiry should say that it is still open. “Cap nut, M8, usual dome” is not complete. Thread class and gauging of the internal thread follow the same rules as other nuts, as in the note on internal threads.
Security and anti-tamper forms need an equally clear drive definition. A unique socket, a one-way head, a shear feature, or a breakaway element is a drawing-controlled geometry. It is not selected from a general “security nut” description, and a matching key or bit is supplied only if the order includes it. The body may also carry a flange or a lock feature; those are additional characteristics, not a reason to ignore the cap, and are discussed in the notes on flange nuts versus plain hex nuts and on prevailing-torque and lock nuts.
Internal thread depth and the closed end
Useful thread in a cap nut is limited by the closed end and by any unthreaded recess under the dome. That length has to be stated, or a standard that defines it has to be named. A thread that is too short for the mating part is not corrected by “tapping a little deeper” if the dome or a residual wall would be compromised. Incomplete threads, runout and remaining wall are inspected as drawn, not traded off on the machine to make a gauge pass.
If the closed end is also a sealing or appearance surface, its form and finish belong on the revision. A polished dome, a coated dome, or a dome that must remain free of marks after coating is a specified condition. Packing that protects that surface, when it is required, is part of the order discussion, as in the note on packing, labelling and lot traceability.
Material, grade, coating and sequence
Property grade, material and finish stay with the print, as in the notes on nut property grades and on coatings for high-strength fasteners. A cap or a security form is not used to infer a stainless grade or a decorative coating that the print does not name. If a polymer insert or a locking element is combined with a cap, the sequence of coating and assembly is agreed, for the same reasons already given for insert nuts. Certificates and any EN 10204 3.1, PPAP or IMDS evidence are confirmed per order when required.
Route and tooling
A cap nut can be produced by heading and forming, by machining, or by a combination of the two, including a secondary closing operation. The route is agreed and is not changed after samples have been approved without a review. A fully machined prototype dome does not by itself approve a later formed dome if the wall, the height or the marks will change. Tooling and process-change rules follow the existing note on cold-heading tooling where heading is used, and the general first-article note on first-article inspection.
Inspection
Height, across-flats or drive form, dome or cap geometry, thread depth and class, and any specified wall or opening at the closed end are inspected as required. A “it looks like the sample cap” check is not a substitute for those figures. If a security drive requires a special gauge or a matching key for inspection, that method should be named in the enquiry.
Open items and volume
A print that names a deep internal thread and a low dome that cannot contain it, or that shows a security drive without defining the mating key, is flagged. Mixed notes that call the part a cap nut in one view and a plain hex in another are reviewed together. Those conflicts are resolved on the revision, not by closing a thin dome on the shop floor or by shipping a standard hex in a cap-nut bag. If the cap is to be used on a gas-equipment accessory, it remains a nut produced to the print; it is not a complete device and it does not carry a type-approval mark unless the drawing of the nut itself requires a component mark.
Volume belongs in the enquiry because forming, machining and any secondary closing operation are not always interchangeable at a prototype quantity. A long series and a short sample lot should be quoted on routes that can be compared at first article. Unspecified construction of the closed end is flagged before tooling is committed.
What to send with the RFQ
Send the current drawing revision with a clear view of the cap or security form and of the internal thread, together with the grade, finish and volume. If a matching key, a particular construction of the closed end, or a first-article layout is already required, say so. Unspecified points will be flagged before production rather than assumed.
This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.