A nut with a nylon or other polymer insert is a prevailing-torque lock nut whose insert type, height and retention in the body are drawing-controlled characteristics. Temperature and media limits for that insert are taken from the customer specification or from a standard the print names. They are not assumed from a catalogue footnote, from a workshop rule of thumb, or from a previous programme that used a similar nut. This article deals with those limits. The broader family of lock nuts is already introduced in the note on prevailing-torque and lock nuts.
What has to be visible on the revision
A complete call-out names the insert material or the specified type, the way the insert is retained, the thread and the body style, and any standard that defines prevailing torque. If a temperature range, a media list, or a restriction such as “not for use with specified oils” already exists, it should appear on the revision or in an attached specification. “Nylon insert, usual grade” is not complete. A type code, including any SH- example used only as an illustration, does not replace the insert description.
The body is not automatically a plain hex. A flange, a prevailing-torque all-metal collar, or a cap form is a different part if that is what the print shows. Substituting a polymer-insert nut for an all-metal lock nut, or the reverse, is a drawing change. Related body styles are discussed in the notes on flange nuts versus plain hex nuts and on cap nuts and security nuts.
Temperature and media are specified, not guessed
Polymer inserts have temperature and media limits, but those limits are not invented here in order to close an RFQ. If the customer specification or a named standard already states a maximum service temperature, a short-term temperature, or a list of approved or prohibited media, that text is followed. If no such limit is given, the gap is flagged rather than filled with a generic figure from a catalogue page. SUNHY does not publish a blanket service temperature or a chemical-resistance table for insert nuts in place of the print.
Colour of the insert is not a substitute for the material type. A red, blue or natural insert can be a colour-only requirement, or it can be tied to a named polymer; the revision has to say which. Re-use, the number of tightening cycles, or a prevailing-torque window after conditioning is included only when the print or the order requires it, not as a default life claim.
The metal body, class and finish still matter
Property class or nut grade, the steel or other metal of the body, and the coating stay with the print, as in the notes on nut property grades and on coatings for high-strength fasteners. A coating process that involves heat can be incompatible with an insert that is already in place; the sequence of coating and insert assembly is therefore part of the agreed route, not a shop habit. Hydrogen-embrittlement relief, when it is required for the body, is confirmed per order and is not assumed to be compatible with every insert type without a review.
Route and assembly of the insert
The body can be headed or machined; the insert is then assembled in a defined way. That route is agreed for the order. A change of insert supplier, insert grade, or assembly method after samples have been approved is a process change and is reviewed before serial use. First-article inspection, when required, should be planned on the production-intent route, including the insert that will be used in series, as in the note on first-article inspection.
Inspection and evidence when required
Thread, body dimensions, insert presence and position, and prevailing-torque checks are used when the print or the order requires them. A “the insert feels tight” check is not a substitute for a specified torque window. Conditioning of samples before the test, if a standard names it, is followed rather than skipped. Certificates, any EN 10204 3.1 evidence, and documents such as PPAP or IMDS are confirmed per order when required. An IMDS or substance declaration, where it is requested, has to reflect the actual insert material, not a generic “nylon” line that the print does not support.
Conflicts, substitutions and packing
A print that names a high service temperature and a polymer insert that the referenced specification does not support, or that calls for a media the insert is not specified for, is flagged. Substituting an all-metal prevailing-torque nut, or a different polymer, in order to “cover” an unstated temperature is not how the RFQ is closed. The customer changes the print if a different locking method is required. Related comments on all-metal lock features remain in the note on prevailing-torque and lock nuts.
Packing and storage conditions, when they are specified, belong in the same conversation, because a humid or a hot store can be part of the customer’s limit for the insert. Those conditions are taken from the order or the specification; they are not invented as a generic shelf-life claim. Volume and the proposed route also belong in the enquiry, so that the quotation reflects the body and the insert that will be used in series.
What to send with the RFQ
Send the current drawing revision, the insert type or material if it is already named, and any temperature, media or prevailing-torque specification that applies. Include the body grade, the finish and the volume. If a first-article torque test or a substance declaration is already required, say so. Unspecified points will be flagged before production rather than assumed.
This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.