Pipe threads on gas-equipment components are drawing-controlled interfaces, not a default that can be assumed from the fact that the part is a stub, a union nut or an adapter. The system, the size and the gauging condition have to be read from the current revision. Catalogue examples on this site — G 3/4 on several brass and steel accessories, and G 5/4 (G 1¼) on some steel stubs — are illustrations. They are not a standard connection offered on every enquiry.
SUNHY reviews these threads on brass connecting stubs, brass union nuts, steel connecting stubs, steel threaded adapters and related turned accessories. The general rules for thread systems, class of fit and go / no-go gauging are in the note on thread standards, pitch and gauging. This note deals with pipe threads on component parts, and with the limit of supply: the part is an accessory, not a complete regulator, filter or station.
Name the system and the size as they are written
A complete call-out names the thread system and the size in the same notation the drawing uses. G-series threads are common on the European examples on this site. Other pipe-thread systems are reviewed when they are specified. A conversion from one system to another is not offered as a substitute for the call-out, and a G 3/4 is not assumed because an example on the product page uses that size.
Internal and external pipe threads, taper or parallel as the print requires, and any note on useful length, stand-off or a gauging reference plane should be visible on the revision that is quoted. If a 3D model is supplied, it does not override the 2D thread data unless the enquiry says so in writing.
Gauging, coating and the mating part
Pipe threads are gauged by the method the drawing or the referenced standard requires. If the finished, coated thread must gauge, that condition has to be written into the enquiry. Zinc plating, which appears as a typical example on many steel stubs and adapters, adds thickness; an uncoated thread that was within limits can sit differently after coating. Over- or under-cutting “to make plating work” is a process decision that must follow the print, not an informal shop practice.
The mating component — for example a union nut against a stub — has its own print. Agreement at the interface is a design responsibility on the customer side. Two parts can be reviewed as a pair if both drawings are sent; one drawing is not used to invent the thread on the other.
Seats, faces and what a pipe thread does not include
A pipe thread on a stub or an adapter often sits next to a sealing face, a chamfer, a bore or a hex. Those features are separate characteristics. They are inspected as specified, and they do not turn the accessory into a complete, tested connection or a PED assembly. Type approval of a regulator or a station is not implied by cutting a G-series thread on a component.
Brass and steel at the same nominal size remain different parts, with different materials and often different finishes. The notes on brass connecting stubs and union nuts and on steel connecting stubs and threaded adapters keep that distinction. Material examples such as CW614N and S355J2 follow the print, as in materials and finishes on European gas-equipment prints.
Route and documents
Pipe threads on these components may be cut or, where the geometry and volume allow, produced by another agreed method. The method is a process decision and is stated rather than assumed. A change of method is re-validated before serial release. Related discussion of rolled versus cut work on fasteners is in the note on rolled versus cut threads; the same principle — the method does not rewrite the call-out — applies here.
EN 10204 3.1 and inspection records are confirmed per order. Gauge records or a stated gauging condition are included when they are specified, not automatically on every lot.
Useful length, the gauging reference and sealing elements
Useful thread length, a gauging reference plane, and any stand-off or unthreaded length next to a shoulder are part of the pipe-thread call-out when the print shows them. They affect both the cutting or forming method and the gauge that will be used. A thread that is shortened to clear a tool, or lengthened to make gauging easier, is not a permitted adjustment. If the drawing is silent on useful length but a mating union nut or a port is also supplied as a drawing, both can be reviewed together without inventing a length on either print.
Sealing elements — an O-ring, a gasket, a tape or a paste — are supplied only if they are part of the component drawing or the order. A pipe thread on a stub or an adapter does not include a seal by default, and a tightness test of a complete joint is not implied. If a component-level tightness or pressure check is required, it is a specified test on the part, confirmed per order, and it is not a type test of a regulator, a filter or a station.
What to write in the RFQ
Quote the thread system and size as they appear on the current revision, together with the gauging condition (including after coating if required), the material, the finish, the volume and the documents you need. Send the component drawing, not a request to manufacture a complete device. Use the request form or email anna@sunhyings.com. A wider list of enquiry items is in what to include in a made-to-print RFQ.
This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.