The drive on a made-to-print screw, bolt or set screw — a hex socket, an external hex, a cruciform, a hexalobular recess, a slot, or a special form — is a drawing-controlled feature when the print states it. Depth, size, gauging and, when specified, the condition after coating all belong with that call-out. They are not completed from a “normal commercial recess” once the head style has been agreed, and a driver that happens to fit is not a gauge.
SUNHY reviews drive geometry on bolts, screws and studs and on some nuts, against the customer drawing. The notes on head styles and on knurling and serrations belong beside this one. This article looks at recesses and socket gauging, and at how the drive should be written in an RFQ.
The designation and the controlling dimensions
A complete call-out names the drive type, the size, the depth or the engagement, and any referenced standard or gauge. “Hex socket” without a size, or “star drive” without a designation, is not complete. If a customer or industry standard already defines the recess and its gauges, it should be named on the revision or attached to the enquiry. A special or non-standard drive is quoted from the dimensions on the print, not from a similar screwdriver in the workshop.
External drives — hex, flange hex, bi-hex, square or a special form — have their own width-across-flats, width-across-corners, height and, when specified, runout or gauging. Those dimensions stay with the head-style review already described in the existing head-styles note. The same print may also control a recess in the opposite end, as on some set screws; each drive is a characteristic.
Forming the recess, and later changes
A recess can be formed in the heading tools, punched, broached or machined. The choice is a process decision and is stated rather than assumed. Formed and machined recesses do not have the same corner fill, the same depth capability or the same surface, even when the nominal size is the same. A machined sample is not approval of a later formed recess, or the reverse. A change of punch, a change of method, or a change of depth after samples have been approved is a process change and is re-validated before serial release — see the notes on cold-heading tooling and on secondary operations.
Material, heading reduction and heat treatment all affect how a deep or a small recess fills and how it survives tightening. If a recess is required in a hard material, in a small head, or after a coating that can fill the corners, those conditions belong in the review. They are not left as a trial on the first serial lot.
Gauging, including after coating
Socket and recess gauges exist for a reason. When the print or the referenced standard requires a go / no-go gauge, a depth check, or an engagement test, that evidence is used; a driver that “fits” is not a substitute. If gauging is required after coating, the coating is part of the condition, because plating and organics fill corners and reduce the effective size. Over-punching “to make plating work” is a process decision that must follow the print, not an informal shop practice.
A lubricant, a wax or a sealer can also change how a bit sits in the recess. The finished condition — uncoated, coated, or coated and lubricated — should be stated when it is already known. Informal oiling of the recess is not part of a made-to-print route unless the specification allows it. The same finished-condition discipline is used on threads, as in the note on thread gauging.
Inspection and first article
Gauge results, measured depth, or a layout of the recess are used when the print or the order requires that evidence, not automatically in every possible form. If a particular gauge, a customer-supplied bit, or a first-article photograph is already decided, name it. A visual check that “there is a socket” is not a substitute for a size or a depth that is written on the print. Cam-out, bit wear or a tightening test, when they are required, are confirmed per order.
First-article or layout inspection, when required, should be planned on the production-intent route, including the method used to form the recess and the coating state in which it will be gauged. Measuring a soft, uncoated, fully machined sample and treating the result as approval of a headed, heat-treated and coated series part is a category error. That rule is the same as in the note on first-article inspection.
Volume and the proposed method also belong in the enquiry. A recess that can be machined on a prototype may be intended for a heading punch in series, and the corner fill and the depth will not be the same in every method. Those choices are stated in the quotation, and they are not changed after samples have been approved without a review. The current drawing revision remains the source of the drive requirement in every case.
What to write in the RFQ
Name the drive type, size and any depth or gauge requirement, including after coating if required, together with the head style, the thread, the material, the property class, the finish, the volume and the documents you need, all as they appear on the current revision. If a customer gauge or a referenced standard already exists, attach or name it. Send the print with the request form.
Send the print. The scope is confirmed before quote.
Email the current drawing revision, or use the request form. Unspecified points will be flagged before production rather than assumed.
This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.