Stainless fasteners appear on automotive and gas-equipment prints in several grades. 304 (often associated with A2), 316 (often associated with A4) and 410 are familiar examples, but they are examples, not a default list. The grade, the condition, any magnetism requirement and the finish are taken from the current revision. An A2 or A4 designation is not assumed when the print is silent, and a 304 bar is not a substitute for a 316 call-out, or the reverse, just because both are stainless.

SUNHY reviews these grades on bolts, screws and studs, on special nuts and on other made-to-print components, against the customer drawing. The notes on material grade and certificates and on carbon and alloy steels belong beside this one. This article looks at what a stainless fastener print should make visible, and at what is not inferred from a familiar A2 or A4 mark.

Grade, designation and condition

A complete call-out names the grade or the standard designation, the condition (annealed, cold-worked, hardened, or a specified strength), and any restriction that a customer material specification already imposes. A2 and A4 are property-class style designations used on many fastener standards; they are not a licence to pick any 304 or 316 melt, and they are not interchangeable with a drawing that names a particular UNS, EN or JIS grade and a particular condition. 410 and other hardenable stainless grades are a different family again: their heat-treatment condition, hardness and corrosion expectations are not those of an austenitic A2 part.

If the print names only “stainless” or only a surface that looks bright, that is an open item, not a licence to use a preferred A2 stock. Equivalence between designations in different systems is not assumed without a stated equivalence on the print or in an attached specification. Mixed notes — a 316 title block and an A2 head mark, for example — are flagged as conflicts. Head marks, when they are required, are produced as specified, as in the notes on head styles and on property classes.

Magnetism, work and heat treatment

Austenitic grades can show some magnetism after cold heading or thread rolling; that is a process fact, not a change of grade. If the print requires a non-magnetic condition, or a maximum magnetism, that requirement belongs in the review, because it can affect the permitted work and any subsequent anneal. Hardenable grades such as 410, when specified, follow the heat-treatment condition that is written on the print, as in the note on heat treatment. An informal shop anneal, or a hardening cycle that the print does not call up, is not a made-to-print practice; intermediate anneals, when they are used, are documented, as described in the note on annealing and in-process softening.

The process route — heading, machining, rolling or cutting the thread — remains a process decision and is stated rather than assumed, as in the notes on cold heading versus CNC and on rolled versus cut threads. Stainless work-hardens; a route that is comfortable in a carbon steel may need a different sequence or an intermediate anneal. A change of route after samples have been approved is re-validated before serial release.

Finish, coatings and corrosion notes

A plain, passivated, electropolished or coated finish is taken from the print. Passivation, when it is required, is a named process, not an assumed consequence of using stainless. Zinc or other coatings on a stainless part are unusual but are followed when specified; they are not added as a “standard fastener finish”. Informal oiling or a polish “to make it look stainless” is not part of the route unless the specification allows it.

Corrosion performance is not invented. A 316 call-out is not turned into a claimed resistance in a particular medium, and a 410 part is not described as equivalent to an austenitic grade. Gas-equipment components that are specified in stainless remain component parts made to the print; they are not complete, tested regulators, valves, filters or stations. Materials and finishes on those parts are discussed in the existing note on materials and finishes on gas-equipment components.

Certificates, inspection and substitution

Material certificates, any EN 10204 3.1 evidence, analysis and lot traceability are confirmed per order when they are required, not issued automatically in every possible form. If a particular certificate, an IMDS record, or a magnetism check is already decided, name it. A verbal assurance that “it is A4” is not a substitute for the document the order requires. Those points are developed in the existing notes on material certificates and on order documents.

Thread and drive gauging, hardness (when a hardenable grade or a specified condition requires it), and first-article inspection follow the print in the same way as on carbon and alloy parts. A substitution of 304 for 316, of A2 for a named 316L, or of an austenitic grade for 410, is a specification change and is not made on the shop floor. First-article inspection, when required, should be planned on the production-intent route, as in the note on first-article inspection.

What to write in the RFQ

Quote the stainless grade or designation, the condition, any magnetism requirement, the finish or passivation, the property class or mechanical requirements if they are stated, the documents you need, the volume and the rest of the part as they appear on the current revision. Send the print with the request form, not a request to use a preferred A2 or A4 stock.

Send the print. The scope is confirmed before quote.

Email the current drawing revision, or use the request form. Unspecified points will be flagged before production rather than assumed.

This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.