A clinch nut is designed to be pressed into a prepared hole in a panel of a stated thickness. The clinch feature, the shank or undercut, and the hole size that feature is intended to fill are characteristics of the component print. They are not a licence to pick a catalogue clinch nut “to suit” a panel that has not been stated, and they are not the same as quoting the customer’s press operation as a SUNHY assembly. On a made-to-print order those installation data are taken from the current revision.
What has to be visible on the revision
A complete call-out names the panel-thickness range or the design thickness, the hole size and its tolerance or preparation, and the clinch or retention geometry that works with that hole. If a countersink, a punched hole, or a laser-cut hole is already defined on the customer’s panel drawing, that condition should be named or attached. “Clinch nut for steel sheet” without a thickness or a hole is not complete. The broader family of installation elements is introduced in the existing note on clinch nuts and rivet nuts; this article deals specifically with the panel and hole data that have to appear before a nut can be produced as drawn.
Head style, body across-flats, thread class and any feeding feature are separate characteristics. They are not invented from a catalogue type code, including any SH- example used only as an illustration. If the nut is a self-clinching type, a pierce-and-clinch hybrid, or a related form, that distinction belongs on the same revision. Pierce geometry, where it is the specified method, is covered in the note on pierce nuts and pierce elements and is not assumed here.
Why a catalogue “grip” is not enough
Catalogue pages often list a recommended panel range and a hole size for a named type. Those figures can be useful as a starting conversation, but they do not replace the print. A neighbouring thickness, a harder panel, a coated sheet, or a hole that has been opened by a previous process can all take the same “type” outside the condition the catalogue had in mind. The RFQ is closed from the drawing and the stated panel data, not from a type number chosen in their absence.
If the customer already has a standard hole and thickness for a programme, that standard should be cited on the revision or sent with the enquiry. A verbal “it is the usual 1 mm panel” is not a substitute. Rivet nuts, which are specified by grip range in a different way, are discussed separately in the note on rivet-nut grip range and body style.
The press process stays with the customer unless agreed
Setting the press, the punch and anvil, the force, and the in-process check of the installed nut remain the customer’s process, unless a written agreement says otherwise. SUNHY quotes the nut as a component. A note that the clinch “must hold in the panel” describes a manufactured geometry and, where specified, a loose-nut inspection of that geometry; it does not include installing the nut or guaranteeing an assembled joint. The same boundary is used for other installation elements in the notes on this site.
Material, finish and the clinch feature
The nut material, property class or performance grade, and the coating are taken from the print. They have to be consistent with the clinch feature and with any restriction on the panel. A coating that builds thickness in the clinch area, or a high hardness that changes how the feature deforms, is reviewed against the revision rather than assumed to be interchangeable with a plain example. Related coating comments are in the note on coatings for high-strength fasteners. Certificates and any EN 10204 3.1, PPAP or IMDS evidence are confirmed per order when required.
Inspection of the loose nut
The clinch diameter or groove, the head dimensions, the thread and any specified relationship between them are inspected on the loose nut as the print requires. A sample pressed into a scrap offcut is not automatic evidence that the hole and thickness on the revision have been met, and it is not a first-article of the customer’s production panel unless that check is itself agreed. First-article inspection, when required, should be planned on the production-intent route, as in the note on first-article inspection.
Orientation features and packing do not replace panel data
A feeding flat or a notch on a clinch nut, where it is required, has to be on the same revision as the clinch feature, as in the note on orientation and feeding features. It does not replace the panel thickness or the hole size. Likewise, a packing method that protects the clinch shank is agreed when it is specified; it is not a substitute for installation data that were never sent. If several panel thicknesses appear in the same programme, each nut item number is quoted from its own current revision. Similarity between two clinch nuts is not a licence to copy a hole size from a sister part.
Conflicts between a nut drawing and a panel drawing — a hole that is larger than the clinch feature can fill, or a thickness outside any range the print names — are flagged before production. They are resolved by a revision or a written customer decision, not by selecting a different catalogue type on the shop floor.
What to send with the RFQ
Send the current drawing revision of the nut, the panel thickness and hole data, and the material and finish. If a first-article layout or a limited installation trial is already required, say so and state who provides the panel. Volume and the proposed route also belong in the enquiry. Unspecified points, including an enquiry that only names a catalogue type, will be flagged before production rather than assumed.
This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.