A made-to-print fastener can start as heading wire, as bar, or occasionally as a cut blank from plate or tube, depending on the part and the agreed route. That starting form is a process decision. It is stated in the quotation rather than assumed, and it is not changed after samples have been approved without a review. A bar that can be turned on a prototype is not automatic approval of a later heading-wire route, or the reverse, just because the finished diameter looks similar.
What has to be visible in the enquiry
The grade, the condition of the starting material, the diameter or the section, and any coating or surface preparation of the wire or bar belong in the enquiry together with the current drawing revision. A note that simply says “steel” or “heading quality” is not a stock call-out. If the print itself restricts the starting form — for example, a requirement that the part be produced from bar, or from a particular wire condition — that restriction is a requirement, not a preference. The named grade remains the grade that is quoted, as in the notes on carbon and alloy steels and on material grade and certificates.
Wire used for heading often arrives spheroidized, phosphate-coated or otherwise prepared for reduction. Bar used for a turned or a mixed route may arrive in a different condition and a different size. Those conditions are part of the route. An intermediate anneal, if it is used to make the next blow or the next cut easier, is documented rather than left as an informal shop heat, as in the note on annealing and in-process softening.
The route and the starting form belong together
Heading, extrusion and thread rolling impose a different flow on the stock from turning or grinding. A fully machined route from bar can place diameters, undercuts and runouts more freely, but it is still only allowed inside the drawing. A headed route is constrained by the blank length, the die and the rollable length. Those differences are already discussed in the notes on cold heading versus CNC and on cold-heading tooling.
Secondary turning, pointing or grinding can be added to a headed blank; that mixed route is still a stated process, not an informal tidy-up. A change from wire to bar, from bar to wire, or from a headed-and-turned route to a fully machined route, is a process change and is re-validated before serial release, as in the note on prototype samples and series production.
Inspection and certificates follow the agreed stock
Dimensional checks, hardness and, when required, a first-article layout are planned on the production-intent starting form. Measuring a turned bar sample and treating the result as approval of a later headed wire part is a category error. Certificates, when they are required, have to match the specified grade and the stock that is actually used. EN 10204 3.1 evidence is confirmed per order when required.
Open items and conflicts
A print that demands a grain flow or a heading-only note, and a request to produce the first samples from bar “because it is quicker”, is a conflict and is flagged. Likewise, a tight concentricity or a deep undercut that a heading die cannot hold may force a machined or a mixed route; that choice is stated in the quotation, not hidden after approval of samples.
Certificates and inspection have to name the stock that was used
When a certificate is required, it has to match the specified grade and it should be reconcilable with the starting form that the route actually used. A bar certificate is not silently reused for a later wire route, or the reverse, just because the grade name is the same. Traceability of the lot, when it is required, follows the agreed stock and the agreed process, as in the existing note on packing, labelling and lot traceability and in the note on material grade and certificates.
Dimensional capability can also change with the starting form. A tight shank, a deep undercut or a precise shoulder may be natural on a turned bar and difficult in a heading die, or the reverse may be true for a high-volume blank. Those differences are reviewed against the print, not hidden by promising the same route “once the tools are ready”. First-article inspection, when required, should be planned on the production-intent stock, as in the note on first-article inspection. The current drawing revision remains the source of the dimensions in every case.
The enquiry should also mention any requirement for grain flow, for a particular reduction, or for a ban on welding or joining starting lengths to make a blank. Those notes, when they exist, belong with the starting-form decision. A heading wire that has been drawn to a convenient size in a laboratory is not automatically the series wire, and a bar cut from a leftover length is not automatically the series bar. If first-article inspection must include a section that shows the flow or the starting structure, that should be stated. Related inspection of the finished heat-treatment condition remains as specified, as in the notes on heat treatment and on core and surface hardness.
What to send with the RFQ
Send the current drawing revision, the material specification, the volume, and any restriction on starting form or grain flow. If a particular wire diameter, bar size or mill condition is already decided, name it. If first-article inspection must be done on the series-intent stock, say so. Unspecified points will be flagged before production rather than assumed.
This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.