The start of a screw or a stud is a drawing-controlled set of features when the print states it: a chamfer, a cone, a dog point, a piloted diameter, a cup or a special lead-in. Those features affect how the part starts in a hole or a nut, how much useful thread remains, and how a thread gauge sits on the end. They are not completed from a “normal commercial point” once the thread size has been agreed, and a photograph of a similar screw is not a substitute for the dimensions on the current revision.
SUNHY reviews point style on bolts, screws and studs and on some turned parts, against the customer drawing. The notes on useful thread length and on set screws and grub screws belong beside this one, because point style is often the first thing a set-screw print controls. This article looks at how to write the lead-in so that it can be produced and, when specified, inspected.
Name the style and the controlling dimensions
A complete call-out names the point style and the dimensions that control it: diameter and length of a dog point or pilot, angle and diameter of a chamfer or cone, and any radius or flat at the tip. “A slight chamfer” or “pointed as usual” is not a dimension. If a standard designation is used, the enquiry should say which edition of the standard applies when the print itself does not. A dog point is not assumed in order to make starting easier, and a pilot is not added because a related part has one.
Pilots and spigots that locate the part in a hole have a diameter, a length and a fit that have to be stated, just as on some installation nuts. If those features are required in production but are missing from the drawing, they are open items, not details that can be copied from a similar fastener. The same discipline applies to a reduced point that has to pass through a stamped hole before the thread engages.
The point consumes length and can affect the route
A long point, a large chamfer or a machined pilot takes length that would otherwise be useful thread or shank. The print has to leave enough complete thread for the class of fit and for any engagement requirement. If it does not, the conflict is flagged. Rolling, heading and secondary machining each produce points in different ways. A point may be formed in the heading die, cut after heading, or turned on a CNC route. The choice is a process decision, as described in the notes on cold heading versus CNC and on secondary operations.
A machined sample with a turned point is not approval of a later headed point, or the reverse. Adding, removing or moving a pointing operation after samples have been approved is a process change and is re-validated before serial release. Die implications, where heading is used, are discussed in the note on cold-heading tooling.
Gauging and inspection of the end
Thread gauges have to start over the point. A large chamfer can help; a damaged or unsymmetrical point can interfere. If the thread must gauge after coating, the point is part of that condition, because coating builds on the end as well as on the flanks. Hardness readings, when they are required, have a location; “end of the point” and “under-head” can give different information, and the specified location should be followed. That point is also made in the note on hardness and tensile checks.
Dimensional checks on a dog point or a pilot — diameter, length, concentricity with the thread or the shank — are included when the print or the order requires them, not automatically in every possible form. If a particular gauge, a CMM layout, or a first-article measurement of the point is already decided, name it. A visual check that “there is a chamfer” is not a substitute for a diameter that is written on the print.
Set screws, studs and special ends
Set screws and grub screws often live or die by the point: cup, cone, dog, flat or a special form, together with the drive at the other end. Those styles are print call-outs, including on stainless items when specified. Double-end studs may have a chamfer on both ends, or a different lead-in on each end; each end is a characteristic. Those families are developed in the notes on set screws and on special studs.
On gas-equipment components, a chamfer next to a pipe thread or a sealing face is often a sealing or assembly feature, not only a lead-in. It is inspected as specified and does not turn the accessory into a complete, tested connection. Materials and finishes on those parts remain with the print, as in the existing notes on gas-equipment components.
What to write in the RFQ
Name the point style and include the controlling dimensions, the thread and its useful length, the gauging condition (including after coating if required), the material, the property class, the finish, the volume and the documents you need, all as they appear on the current revision. If a mating hole or nut drawing exists, attach it for information. Send the drawing with the request form.
Send the print. The scope is confirmed before quote.
Email the current drawing revision, or use the request form. Unspecified points will be flagged before production rather than assumed.
This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.