Process capability on a made-to-print part, when it is required at all, is calculated for named characteristics under an agreed plan. It is not a blanket Cpk or Ppk for a factory, a product family, or “fasteners in general”. A figure published as a site claim, or copied from another programme, does not replace the requirement on the current order.
SUNHY can include capability studies for drawing-controlled characteristics when the customer specifies them. Like first-article inspection, PPAP content and EN 10204 3.1, this work is confirmed per order. It is not an automatic attachment, and it is not a substitute for meeting the tolerances on the print.
Name the characteristics and the index
The enquiry should say which characteristics are to be studied — for example a pitch diameter, an under-head radius, a body length, a sealing-face dimension, or a hardness range — and whether the index required is Cpk, Ppk, or another stated measure. “Cpk 1.33 on the part” is not a complete instruction. Attribute characteristics, such as a go / no-go thread, need a different treatment from a measured variable; they should not be forced into an index that the method cannot support.
The drawing already decides which dimensions are tolerances and which are reference or auxiliary. Capability is planned only for the characteristics that the customer identifies. A reference dimension is not turned into a capability study by default.
The process condition has to be the series-intent process
A capability study is only meaningful on the process that will run in series: the same route, material heat, tooling family, heat treatment and coating, or a documented and accepted difference. Data from a fully machined prototype, or from a temporary supplier of a special process, should not be presented as series capability. That is the same principle as in the notes on prototype samples and series production and on first-article inspection.
A later change of die, route, coating source or material grade is a process change. Existing capability data do not travel with that change unless the customer agrees that they still apply, or a new study is made. The note on cold-heading tooling and die changes is relevant on headed parts.
Sample size, method and software are part of the plan
The number of parts, the lot or lots they come from, the measurement method and the rules for outliers or for non-normal data should be agreed, preferably by reference to the customer’s standard. If a particular form, software output or statistical method is already required, name it. Informal “we ran thirty pieces” notes are not a study.
Measurement variation matters. If a gauge-repeatability or measurement-system check is required alongside the capability study, it should be stated. The method used to measure the characteristic — CMM, micrometer, thread indicator, hardness tester — has to be the one that the plan describes, and it has to be capable of resolving the tolerance.
What a capability index is not
A capability index is not a PPM guarantee, not a substitute for inspection where inspection is specified, and not a licence to widen a tolerance. Optical or automated sorting, when the order requires it, is a separate control; it does not create a capability figure, and it is not an automatic claim, as already noted in the article on order documents.
Quality-system certificates are also not evidence of a capability index. ISO 9001 may be referenced as a framework; entity, site, scope and validity are confirmed before any certificate is cited. A capability study, if required, still has to be planned for the characteristics on the print. Nothing in that study widens a tolerance or replaces the inspection that the drawing or the order already requires.
Short runs, special processes and when a study may not apply
Some made-to-print items are needed only in small quantities, or only for a short programme. A capability study that assumes a long, stable series may not be the right request in that case, or it may need a different sample rule that the customer writes down. It is better to say that a study is not required, or to name a reduced rule, than to leave a generic “Cpk 1.33” on a purchase order for a handful of parts. The quotation will not invent a series figure in order to look complete.
Special processes such as heat treatment and coating introduce their own sources of variation. If capability is required after those processes, the study has to be run on parts that have actually been through them, not on uncoated or unhardened blanks. If the special process is performed by a subcontractor, a change of that source is a process change, and existing indices do not travel automatically. That point belongs in the programme documents if capability is a live requirement.
What to write in the RFQ
If a capability study is required, name the characteristics, the index and the target, the production-intent process, the sample size or the governing standard, and the format of the report. Include the current drawing revision, material, finish, volume and any other documents you need. Send the drawing with the request form or to anna@sunhyings.com. A wider list of enquiry items is in what to include in a made-to-print RFQ.
This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.