Not every number on a made-to-print drawing is an inspected characteristic. Some dimensions are reference or auxiliary; some are basic dimensions that locate a geometric tolerance; some are stock or theoretical sizes that the title block or a standard already explains. The inspection plan follows the way those items are identified on the current revision. Reference or auxiliary dimensions are not treated as tolerances by default, and they are not ignored when they actually carry a tolerance or sit inside a feature-control frame.

What has to be clear on the revision

A complete scheme identifies inspected dimensions with tolerances, marks reference or auxiliary items as such, and places geometric controls in feature-control frames with datums. If a customer uses a ballooned drawing to say which items are inspected, that balloon set should be consistent with the drawing, as in the note on Ballooned drawings and layout inspection. “Inspect everything on the sheet” is a possible request, but it has to be written; it is not the default reading of a reference dimension.

Basic dimensions used in a geometric scheme are not inspected as plus-or-minus sizes unless the print says so. The geometric tolerance is inspected, against the stated datums, as in the note on Datums and geometric tolerances on turned parts. A model nominal is not a tolerance, as in the note on The 3D model versus the 2D drawing.

How the plan is built

In-process and final inspection, sampling, and any layout are built from the inspected characteristics and from notes that require a check. Measurement methods follow the note on Measurement system and gauge agreement. Thread gauging, roughness, coating thickness and tightness checks remain on the plan when they are specified, even if they are written as notes rather than as boxed dimensions. A reference overall length does not replace an inspected length that is held from a datum.

First-article inspection, when required, reports the inspected characteristics and the required notes, not a catalogue of every reference number on the sheet, unless the customer has asked for that broader list, as in the notes on First-article inspection on made-to-print parts and on Ballooned drawings and layout inspection.

Conflicts and informal expectations

A dimension marked reference on the view and given a tolerance in a table is a conflict and is flagged. A general note that “all untoleranced dimensions are ±0.1” and a clearly marked reference size are read together, not used to invent a tolerance on the reference. Those stack questions follow the note on Specification stack and order of precedence. An informal request to “watch” a reference size because it helps assembly is recorded only if the customer makes it an inspected characteristic or a written process target.

Similarity in a family of parts does not turn a reference size on one item into an inspected size on another. Each revision is read as it is drawn, as in the note on Quoting a family of similar parts.

What this does not authorise

Treating reference dimensions as non-inspected by default is not a licence to ignore function, and it is not a licence to change the part to make machining easier. If a reference size is the only place a needed limit appears, that is a drawing weakness and is flagged so that the customer can add a tolerance or a geometric control.

Stock sizes, “typical” views and inspection records

Stock or commercial sizes shown for information, “typical” views, and development lengths taken from a bent model often appear as reference. They help the reader, and they can mislead a planner who copies them into a gauging box. The inspection record should list inspected characteristics clearly, so that an auditor can see why a reference length was not reported. If a customer template forces a value into every balloon, including reference balloons, the handling of those lines is agreed in writing rather than filled with a guessed number.

In-process targets used to hold a process centred are not the same as drawing tolerances. A process target on a heading length can be useful and should remain internal unless the customer has asked for it. Publishing an internal target as if it were a reference dimension, or tightening a reference into a secret tolerance, will confuse later lots and later auditors. The print says what is inspected; the process plan says how the process is steered.

Software and CMM programs can also quietly promote every extracted CAD size into an inspected size. The program should follow the ballooned or toleranced set, not the entire model tree. A measured reference value may be recorded as information when the customer asks for it, clearly marked as reference, and not used as a pass/fail unless the authority has changed. That discipline keeps the plan honest when a later auditor compares the report with the drawing.

If the customer later elevates a former reference size to an inspected characteristic, that change appears on a new revision or a written instruction before it is added to the plan for the next lots.

What to send with the RFQ

Send the current drawing revision, any ballooned list of inspected characteristics, and the material, finish and volume. If every dimension, including reference items, must be reported at first article, say so. Unspecified points will be flagged before production rather than assumed.

This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.